(800) 853-2651
SHOP NOW

Recent content by henrye4020

Yesterday's Tractor Forums
  1. H

    John Deere 953

    They are thread in, they have the unmistakable JD stamp on the end.
  2. H

    John Deere 953

    I am in search of a (1) hubcap for a 953 running gear. You fellas know of any sources? Thanks, Henry
  3. H

    Farmall H not timed?

    I suppose this is a fairly common question, but after about 2 years of sitting (it ran before) in an insulated shop, I cannot get my h to start. We put new plugs and a cap on it before trying, and it has good spark. After turning it over for a while, it will leak fuel out of the carb, so I am...
  4. H

    John Deere 70 Belt Pulley

    Andy, I just did mine last winter and was wondering the same thing. Originally I tried a puller, but but it would bore holes in the piece of 3/8 steel I was pushing against. Eventually I got fed up and sent it down the road to my mechanic who pressed it off in a jiffy, then pressed it back...
  5. H

    Power Trol Selctor Valve

    I have a few questions about the Power Trol on my 70. Selector valves- 1 or 2? There has been a lot of confusion on whether one is sufficient or not. Also, where can I find one? Any good salvage yards out there that carry these? Thanks, Henry
  6. H

    70 Diesel Governor

    Thanks guys, I appreciate you getting back to me. I think what I will end up doing is going through the pony- new coils, transmission parts, oil pump, etc. Maybe an overhaul? It smokes really bad. Is this normal? Dad says no, but I wanted to be sure. Any advice? Henry
  7. H

    70 Diesel Governor

    I have a '55 70 diesel that I think has governor problems. It has problems holding engine RPM even when moving on its own. It idles up just fine, but it won't hold RPM's without messing with the throttle under load. What could be wrong, and what would it take to fix it? Also, what are you...
  8. H

    37 Sickle mower

    Thank you all for replying! The John Deere trademark is no doubt a symbol of quality and service...which is why much of this old equipment is still here today. If I was to make one from scratch, how long would it have to be? I know that it is angled a little to the left (when looking from the...
  9. H

    37 Sickle mower

    I have a sickle mower (John Deere 37) with a broken suspension arm. It was broke before I bought it. This is the arm that lifts the sickle. The piece that the chain hangs on is the part that is broke. My question is: is it fixable, can I weld something on there to make it work or do I have to...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top