(800) 853-2651
SHOP NOW

Recent content by herne19d

Yesterday's Tractor Forums
  1. herne19d

    Farmall Super C hand crank location

    The pictures aren't there anymore. The links are dead. Thanks though!!!
  2. herne19d

    Farmall Super C hand crank location

    Thanks!! This will help a lot until I can find the actual mount!
  3. herne19d

    Farmall Super C hand crank location

    It's a little different because of the hydraulic lines, but this gives me a good idea. Thanks!!
  4. herne19d

    Farmall Super C hand crank location

    Ok, time for my next question. Where does the hand crank get stowed on a Super C? I have a 1953 and I found a picture of a part and a diagram on Burch Store Tractors that shows where it goes. Does anyone have a picture of a tractor with one mounted? The tech drawing isn't showing...
  5. herne19d

    1945BN Mag Timing

    Thanks for the picture! I wish the timing marks were there, it would have made life a lot easier. What's that saying? The only easy day was yesterday?? Hah! Thanks again to everyone for all the help!!
  6. herne19d

    1945BN Mag Timing

    Yeah, that was part of the trouble I ran into. Someone had sanded/ground the gears and the Mag gear and the intermediate gear have no marks on them. It took a while for me to get it sorted and set up so that the impulse kicked at TDC. Thanks!
  7. herne19d

    1945BN Mag Timing

    Sitting in the seat, the rotor turns clockwise. Yes, it has run since I rebuilt it. The problem is that it only starts with the starter and the impulse spring released very late. I've gotten to where the impulse spring releases at exactly TDC, and I haven't tried it by hand yet. Having time to...
  8. herne19d

    1945BN Mag Timing

    Thanks for all the advice! I pulled the radiator off, took the governor off and, lo and behold, there are no timing marks on the mag gear or the intermediate gear. I wiped then off and looked with a flashlight, nothing there. So, I took the mag off, pulled the drive gear out and then...
  9. herne19d

    1945BN Mag Timing

    Yuppers, did that. That's what the problem is, turning it away and it doesn't Trip. I turned it as fast is it goes, to the end of the bracket. To get it to Trip, I actually have to crank the engine well past TDC. Thanks!
  10. herne19d

    1945BN Mag Timing

    I did that. Like I said, I did all the things and followed the directions right out of the owners and shop manuals. Thanks though!!
  11. herne19d

    1945BN Mag Timing

    It's an H4 and in good working order. I'm thinking that the gears weren't lined up properly amen it was last rebuilt. I just want to see if other folks agree, or if I'm way of track. Thanks!
  12. herne19d

    1945BN Mag Timing

    I've got a 1945 Farmall BN and when I go to set the magneto, I crank the engine to TDC cylinder 1, and set the Mag so that the rotor points to the #1 plug wire, mount the Mag with the top of it as close to the engine as possible, crank it fully around, back to TDC for #1, and then advance the...
  13. herne19d

    Three point hitch

    To the guys who had the helpful answers, Than You very much. I found a part that will work for a decent price. To those who did not actually read what was written and made assumptions and snarky answers, not so much. It is correct, I did not put the year or make. And I said "similar to"...
  14. herne19d

    Three point hitch

    I'm looking for a quick-adjust leveling arm that will fit my TC-30. Something like the ones that are found on 8N and 9N Fords. New Holland sells one, but it is $450+. Any help would be great.
  15. herne19d

    Trying to ID an IH Single Bottom Plow

    The other question is; Is there a way to figure out what year this plow is from? I just bought it, I haven't scrubbed it with a wire brush yet, the only number I found was the one on the eccentric hub. Is there a serial number on it somewhere?
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top