(800) 853-2651
SHOP NOW

Recent content by Herpdawg

Yesterday's Tractor Forums
  1. H

    JD 145 gas oil pressure issue

    Hey guys. Put the 145 gas engine in my 1010. Tore it down and cleaned everything. Not sure why I can't get oil pressure to the gauge. New line and new gauge. I have some pressure because it comes out the plug in the block. First oil pump was cleaned. Put a second pump in with same result...
  2. H

    1010/2010 engine swap

    Thanks for the reply. For now I think I will use the 1010 manifold and carburetor and see what happens. It is not going to be used a bunch anyway.
  3. H

    1010/2010 engine swap

    I wondered about that. Will look in to that. Thanks
  4. H

    1010/2010 engine swap

    Just put a 145 gas engine from a 45 combine on a JD 1010 tractor. Rus pretty good. I put the manifold and carburetor from the 1010 115 engine on the 145. Part book numbers are different for the heads. Carburetors are different. Will it be absolutely necessary to put a 145 tractor manifold...
  5. H

    300 MF Combine

    Thanks. I will check it out.
  6. H

    300 MF Combine

    I have a 300 MF combine (serial number 189XX) gasser that is needing a new electric fuel pump. The one I took off is a Facet cylindrical type with one wire. Wondering if anyone had any ideas of a good replacement. I am not sure of pressure requirements, minimum dry lift, or any other stuff...
  7. H

    60 starter

    All ends are clean. Could be that coil. Spins good out of tractor but struggling to roll tractor engine. Thanks
  8. H

    60 starter

    Will check that next. Thanks.
  9. H

    60 starter

    Actually just moved it below the box attaching it to the bolt below it. No difference. The battery is good and it is 850 cca. Same battery as what I have in my Dodge Cummins. Thanks for the reply.
  10. H

    60 starter

    The starter on my 60 barely rolls the engine over, but just enough to start it. Have had it to a starter shop and they say it is fine. Even with a new battery and new cable, nothing changes. Thoughts? Thanks
  11. H

    2510 tsx 905 carburetor

    Carburetor is overloading. Have new needle and seat. Was wondering what proper float level is. Do you check with gasket on or off? Any info appreciated.
  12. H

    440 pressure plate

    Having problem bolting engine to bellhousing. With clutch aligned and throw out bearing in, block lacks about an inch from bolting up. With throw out bearing out of tractor, engine bolts up. Auburn pressure plate patent number is 1885301-2214780. Not sure if this is the correct pressure...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top