(800) 853-2651
SHOP NOW

Recent content by hrbburn

Yesterday's Tractor Forums
  1. H

    John Deere 60 Oil Pressure Adjustment Different

    BuickandDeere, So the section 13 engine 15 is the setup we have img 6037. So if we just take that plug out of the side of the tractor I expect oil would run out, and it does not. A friend that has rebuilt a few of these old tractors said he don't think we let it run long enough to build presure...
  2. H

    John Deere 60 Oil Pressure Adjustment Different

    Some added info. This engine was rebuilt and will start and run but seen it does not show oil pressure after a minute or two so shut it down. Pulled the as mentioned different type of pressure adjustment out to see if any oil bypassed. No oil comes out of it at all. Because we are not sure if...
  3. H

    John Deere 60 Oil Pressure Adjustment Different

    I have a JD60 and currently no oil pressue. I see other post on here on where and how to set the oil pressure but mine is different. What I have saw is loosen a jam nut on the side and adjust the pressre screw. Mine doesn't have that setup. You take a pipe plug out then there is what would...
  4. H

    JD720 Lower water pump tube install. Fought getting the tube pressed in the oring from the pump to the motor and have exhausted every thing I can thin

    I have cleaned it up good on a wire wheel bench grinder. Can you clarify on your comment about prying up
  5. H

    JD720 Lower water pump tube install. Fought getting the tube pressed in the oring from the pump to the motor and have exhausted every thing I can thin

    The tube is OEM but they are straight no bends. Seems like they should have a bend but they don’t.
  6. H

    JD720 Lower water pump tube install. Fought getting the tube pressed in the oring from the pump to the motor and have exhausted every thing I can thin

    The tube has about 1/4 in long chamfer on both ends. But we have tried so much pressure and twisting and it doesn’t seem to even get close. Tube has plenty of clearance without oring and oring slides right on when not installed
  7. H

    JD720 Lower water pump tube install. Fought getting the tube pressed in the oring from the pump to the motor and have exhausted every thing I can thin

    Any suggestion how to install this pipe without pushing the oring out Used soap. Oil lube and grease and just can’t get the tube to press in. Any help greatly appreciated
  8. H

    Ford New Holland 1620with 7108 bucket

    I am looking for a bucket level rod kid for my 7108 bucket but have not been able to find one online anywhere. Any suggestions
  9. H

    John Deere B Magneto

    I got an old John Deer B that hasn't ran in about 3 years. It was running when parked, or at least thats what they always say. Anyway don't know anything about a magneto and thought that might be the place to start. It cranks over but has no spark at the spark plugs. The mag spins and the points...
  10. H

    Massy TO35 Wheels

    I have the power type wheels both are shot from the calcium. I haven't seen anything but wondering if there is a replacement wheel that will bolt up to the existing centers I have for the power wheels? Any help would be greatly appreciated. Thank you, Bud
  11. H

    TO35 Cylinder head

    Does anyone have pictures from a manual that shows the part of the T035 gas head. I dropped a valve and it looks like a cylindrical part also. Is that just a guide for the valve spring?
  12. H

    MF35 vs TO35

    I have a TO35 but when looking for parts most just say MF35. Can someone tell me the difference between a TO35 and MF35. Also my power steering is leaking from up under the dash. I see a seal in the parts list but it just says for a 35, would it be the same for a TO35? Thanks in advance for any...
  13. H

    Massey Ferguson To35 Broken 3 Point

    Can some one suggest how to repair. On my 3-point my adjustable side crank will turn about 1 turn either way then locks solid. It was working fine and took my tiller off to put my blade on and now it won't work. I tried tapping it a little in both directions and it would not move at all except...
  14. H

    Massey TO35 flywheel spec's

    Thank you, the more I think about it I think that I will skip getting it turned. Thanks again. Bud
  15. H

    Pulling transmission main drive gear TO35

    Ok, still working on replacing the clutch on my TO35. I need to replace a seal between the pto and main shaft as that is where it is leaking. The manual is not clear to me. If just pulling this main transmission drive gear, can I just unbolt the four bolts and pull it out? The manual talks about...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top