Recent content by IronAddict

  1. I

    861 Nature of the beast?

    Hello all I have a 1958, 861 that I have been using to clean my one acre pond with. When I go down hill in forward the oil pressure will drop to zero! It normaly is above 40psi.Going up hill is fine. I will guess that the grade to be about 2 on 1. The grade is no worse than some fields...
  2. I

    W-4 C 152 cam

    Hello all I am rebuilding the second of my 3 W-4's. The first one went so smoothly. Only needed the basic overhaul kit (sleeves and pistons) I figured the second would be similar. ..not so lucky! After checking out the crank I decided that it should be ground so I had that done and bought...
  3. I

    W-4 Thick felt seal

    thanks Bob! I checked it out and they do have what I need. I have dealt with that company before and they are great.
  4. I

    front loader for Cub

    I have one in Western NY for sale as well if anyone is interested. ..Iron
  5. I

    W-4 Thick felt seal

    Hello all I need to find some felt for a seal. The approximate size is 1" square by 30 inches long. Felt is what was used to fill the gap between the bell housing and tractor frame. ..I guess you would call it the bell housing, it"s the cast plate that bolts to the back of the motor. I...
  6. I

    OT

    was wondering if anyone here has experience with a plasma cutter? What happens when you hit a spot of rust or dirt? Thanks Iron
  7. I

    Best Place To Buy a Zenith Carb?

    If you are the CEO of Vandelay, ...beware of stout balding guys!! ..Iron
  8. I

    looking for ford 4000

    A friend has one for sale here in Western NY State, but i think it might be the later model. It"s a 3 cylinder gas,and has a loader on it. That"s about all I know of the machine. ..Iron
  9. I

    4000

    Suprised the heck out of me. Didn"t realize that there were 3 cylinder "gas" engines. ..Learn somethin new everyday! This tractor is of that type and is located in Western N.Y.State. ..Iron
  10. I

    4000

    Thanks for the info. He hasn't found the number yet but it has to be the older series ..it's a gas job, 3 cylinder motors would have to be diesel I'm thinkin. ty ..Iron
  11. I

    4000

    I"m trying to help a friend out who needs to sell a 4000. Can you guys give an aproximate value on a Ford 4000 (gas), has a loader on it. Need to know the location for the serial number also. Thanks in advance ..Iron
  12. I

    w9 and disk. pics.

    I'm not familiar with W-9's. Is that a hydraulic pump on the PTO? And do you wear ear protetion while running that beast? ..I use ear muffs while using my 4 ..Iron
  13. I

    W-4 Serial Number

    John The decals were at some point changed. The early 4's had McCormick Deering on the side of the hood,and the later ones only had McCormick. I don't know off hand what year they changed ..Iron
  14. I

    Shifting into 5th Gear on a Farmall

    I personally prefer to double cluth my W-4 when I am going for 5th gear. Bucky ..I was wondering if you knew the correct procedure of double clutching ..as many do not these days. It is a bit tricky but can be done. You need to be going full throttle in 4th and then shove the clutch in,drop...
  15. I

    My Dad bought a 1949 W-4

    My 1941 W-4 has always been on rubber as far as I know, but it was available on steel. There is a place for a bolt to be put in that will prevent 5th gear from being used with the steel. ..Iron
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top