(800) 853-2651
SHOP NOW

Recent content by Irv B

Yesterday's Tractor Forums
  1. J

    Ford 801 / 871 Fluid leak

    Suspected O-Rings on Hydraulic manifold. Was incorrect. There appears to be a hole where there is not supposed to be one. Can anyone shed any light on this. Hydro Fluid exits pretty quickly when running. Hole is circled in photo.
  2. C

    Pin sizes on top link, 2n,8n,600

    Is the diameter of the differential mount pin on the top link the same on 2N, 8N, 600 ? Need to replace pin for the longer pin for model 14-15 Dearborn mower mount. Charles Krammin
  3. J

    4500 hydraulic hoses

    I"ve got a 4500 TLB that one of the four hoses that feed into the dipper arm is leaking. These hose connections are very close together and back in a recess area. Can"t get at it with regular 1 1/4 open end wrenches. Got a 1 1/4 tubing line wrench coming next week to try. There must be a thin...
  4. C

    720 D fuel in muffler

    I finally got my 720 D running after setting for some 20 years in the barn with being started. The diesel engine started right up after I finally got the pony running correctly. With the diesel running, now I am seeing some dripping of diesel fuel coming from where the muffler connects to the...
  5. C

    656 Hyd Remote Valve

    Farmall 656: Single remote hydraulic valve leaking oil badly. Is there a cure available. It appears that parts from Case/IH are no longer available.
  6. C

    JD 6300

    Our 6300 loader tractor is causing me grief. It works great loading for short periods- loading, moving stuff, anything non taxing. Usually runs 10 min to 45 min at a time, not really working hard so its no problem. I hook up the side arm flail mower and mow ditches this time of year...
  7. I

    White SN plate

    do you know what it looks like?
  8. R

    435 baler auto twine

    the auto twine on my 435 is not working. the warning light does not blink just comes on solid and the arms dont move. When I manually tie (with the rope) all works fine. I know my springs are all good, and the pump has fluid. Just got the baler and it had been sitting for 2 years. thanks in...
  9. I

    540 Cockshutt 3 pt hitch help

    you have what is called the servo valve which is used only for the 3 point. The oil actually enters and leaves the valve on the bottom side when valve is activated by using the handle on right. The oil passes through ports in the casting to the lines to move the hydraulic cylinder that should be...
  10. I

    540 Cockshutt 3 pt hitch help

    I have a couple pictures of a 550 which uses the same system as the 540. There are a few suttle differences like the draw bar, pump placement, seat mounting, and the lift links and draw arms are a little shorter. they also don't use the sway bar on the 540. what more specifically do you need...
  11. I

    Cockshutt 30?? Help

    Nice looking 30. If you look on top of the frame rail adjacent to the distributer almost right over the round hole in frame. The serial number will be there which will tell you the year for sure. It will start with a 30 for model then a space and a 5 digit number starting with 17370 on up will...
  12. C

    1070 Case what to look for

    I have a couple 1030's but am going to go check out a 1070. What do I need to watch for when looking at it, the powershift is supposed to be tight, that will be the first thing. Will use it on a discbine and batwing mower. Are the 1070's much better than the 1030's? Any help will be much...
  13. B

    Farmall 240

    This message is a reply to an archived post by farmallhal on April 18, 2013 at 06:46:06. The original subject was "Re: Farmall 240". I just bought a 240 row crop. looks like it had something mounted on the front half, maybe cultivators. The hydra touch has only one lever, all the pictures I...
  14. I

    painting and preping a ford jubilee

    what will it cost and is there anyone in Dakota county Minnesota willing to prep and paint a ford jubilee? how much should I exspect to pay for an average or nice paint job it does not have to be perfect. Thanks
  15. I

    cockshutt 570 super pistons

    If you are interested I have 5 new old stock standard pistons for the 339. Jerry Biro as all ready mentioned probably has some also. He may have a complete set to sell and he may sell a single. I am in western Pa and have some parts for the cockshutts. Irv
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top