(800) 853-2651
SHOP NOW

Recent content by j williams

Yesterday's Tractor Forums
  1. J

    Oliver 550 won't start.

    Did you get the 550 started? You Stated that you had the carburetor rebuilt. Just wondering if the Venturi was put back in upside down.
  2. J

    Oliver 550 won't start.

    Have you checked the muffler and exhaust pipe for obstruction possible mice or birds made nest in it Also to check firing at plugs take one out and with a pair of insulated handle pliers hold the plug with it hooked up to spark plug wire against the motor block and have someone crank the...
  3. J

    550 wheel bearing

    Thanks for the bearing info
  4. J

    550 wheel bearing

    Can someone give me the bearing number for rear axle outside bearing 1960 oliver 550. The bearing i took off is a hyatt bearing but i can't make out the number.
  5. J

    Running rough after hibernation

    When you serviced the oil bath breather is it possible you pushed the breather tube down any. I had this happen to me on my 880. I took the hood off just to clean and wash motor when i put it back on, tractor was hard to start and would not speed up. Come to find out the robber grommet on the...
  6. J

    70 industrial

    Well as it turns out, i was able to answer my own question. After reading the parts page again a little closer, it reads that you use one additional front bracket (part #B-1258 ). for the rear light bracket on the industrial model. It mounts on the right rear fender down lower by seat.
  7. J

    70 industrial

    Anyone have a picture of a rear light bracket part #F-1367 for a Oliver 70 industrial year 1945. My parts book has the part # but does not show a picture of it. Also where would it mount on rear fender?
  8. J

    70 industrial

    Starting to put engine back together. ( continental DS6202 ).My question is should i use gasket sealant on head gasket or not. if so what type .The gasket is a metal gasket with cooper around water ports.
  9. J

    Power booster repair?

    I replaced the spraug clutch in my 880 about 8 or 9 years ago with one made for a 2-105, AGCO part # 72161793. I was told keep the transmission oil a quart above the filler drain plug. Unit has been working fine.
  10. J

    Oliver 70 Industrial, Rear rims

    The industrial does not use lug rims the proper rims have a bevel in places where the bolt is bolted to the center hub.
  11. J

    engine parts

    YES Gambles you have me pegged to a tee. I don't want to try to figure out how much money I have spent in Old tractors. Some people get hooked on drugs i got hooked on Oliver tractors. And yes i have priced Oliver 70 parts. But it just needs to be brought back to its glory days.
  12. J

    engine parts

    Brad can you Email me or give me a call 240-925 -0789 John i would like to talk to you about your article
  13. J

    engine parts

    Thanks for the reply Have a phone # and what state are they located
  14. J

    engine parts

    Anyone have a source where i could get Sleeves and pistons, rings for a Oliver 70 industrial serial # 400604 it has a continental engine. The Block # is D600A619 Korves Brothers have some parts but not Sleeves and pistons.
  15. J

    550 engine

    I just purchased a 550 with serial # 81248-519 specification # 45-0254 Which i find to be a mid year 1959 model . I believe Oliver changed the piston size sometime during that year. Can someone tell me whether i have the smaller version or the larger size.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top