(800) 853-2651
SHOP NOW

Recent content by jackbrit

Yesterday's Tractor Forums
  1. J

    OT Car Maintenance

    I would take a good look at the underside for RUST before I would rebuild front.
  2. J

    OT:FWD whl brg,got bolts out, now what?! GM experts

    To remove the hub bearing on my jeep, I used a socket extension jammed into the right spot and used the power steering and turning the steering wheel to pop it out. Sure did beat the hammer and wedge!
  3. J

    gear replacement push mower

    The angled flat gear the teeth are just about worn off in the middle of the gear.
  4. J

    gear replacement push mower

    push mower gear drive box There are two actual gears in this box. One is a worm gear and the other is a flat gear with cuts on an angle. Should these gears be replaced as a SET or just the one that looks worn?
  5. J

    O/T Coolant Loss

    Check real close just to the front above the top of the water pump. I had been loosing coolant for a while and it was evaporating on the hot engine until it got more serious. There are two plastic elbows one just in front above water pump and one lower to the rear. They sell for $5 and are...
  6. J

    chinese valve rant

    Does it make any sense to have an almost entire brass valve, except for the screw made of carbon steel holding on the seat washer? You can guess what happens in a year. Where do you buy your replacement valves?
  7. J

    Sweetfeet, results of fluidfilm on rusty Regular

    I sprayed it in every hole I could find when replacing my jeep YJ frame. These box frames rot from the inside out.
  8. J

    Drilling holes in glass tile

    drill press, copper pipe, grinding compound, clay wall around the area with a coolant? The spinning pipe is the bit and compound abrasive is the cutter.
  9. J

    O.T. - Fridge trouble

    Is the fan between freezer and fridge working, mine needed a lube job.
  10. J

    Lincoln Welder, what's it worth?

    I would keep looking for ac/dc and spend about $175, they almost never die.
  11. J

    1991 dodge van water pump

    Well I did this water pump today, just about 4 hours. I did use 9/16 10mm and 15 mm. There was lots of things in the way. When all done the van DID NOT START(no crank) , all I did electric was remove negative cable off battery. Jumped starter and solonoid with another battery and took it to...
  12. J

    1991 dodge van water pump

    should I bring the metric sockets and wrenches or the standard ones to do this job?
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top