(800) 853-2651
SHOP NOW

Recent content by JBF

Yesterday's Tractor Forums
  1. J

    830 parts for sale

    I just bought a 830 COM. I"m going to use the engine and the radiator, everything else is up for graps. There is a photo of it on the photo ads page. Thanks
  2. J

    H Govenor

    Can the H and M govenors be switched? I just bought a govenor of ebay supposedly for an H. The carb control rod was about 3/4 of an inch longer than mine and the neck ontop the gov was taller along with the control rod from the govenor. The gears had 16 teeth on mine and 17 teeth from the one I...
  3. J

    830 engine

    I'm looking at replacing the bad motor out of my 66 830 comfort king with a moter out of a ealier 830. The ealier 830 has the decompression heads. Is there any other differece between these motors? HP? Will they interchange? One better then the other? Thanks
  4. J

    830 heads

    Can the decompression heads be switch over to the none decompression heads? Are they the same bolt pattern?
  5. J

    830 worth

    Looking at a 830 caseomatic, clam shell fenders, straight sheetmetal, wide front, the motor is tired but runs with leaks every where. What might this thing be worth?
  6. J

    Case 830 motor swap

    Will a 336d bolt up in place of a 301d. If it fits does anyone have onr of these motors for sale? Thanks
  7. J

    Need 830 motor

    The problem is the tractor sat for 1.5 years and was full of coolant without the oil pan on. I didn't see any dripping coming from around the sleeve orings. The heads look ok as well as the head gaskets when I took them off. I had the motor laying on the manifold side for 7 days, I don't know if...
  8. J

    Need 830 motor

    Tearing down a 301d from an 830 I just bought. I take off the oil line running to the injection pump and antifreeze comes out from the oil gallery. I don"t know if this can be fixed? So I"m looking for a complete running motor just to bolt back in a go. Anybody have one? Thanks
  9. J

    830 western special

    I have the narrow fenders, not the big wide ones. The rear axles are tapered with a nut and have 30" cast hubs, unlike the other 830s I've seen with the clamp on style hubs. Thanks for the info.
  10. J

    830 western special

    The model number is 832 and the serial number is 8284099 i think. This tractor has the western front end tucked up under the front of the motor and has three point (draftomatic) with the comfort king fenders not the round style.
  11. J

    830 western special

    Does any body have any info on the 830 western special. I just picked one up with a bad motor. Its a comfort with draft o matic. Nice tractor but spun a main bearing. Does any one have a good crank for sale? Also looking for a decent set of comfort king fenders for it and a wrap around seat...
  12. J

    H clutch (flywheel) step

    What is the correct step on a H flywheel? Thanks
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top