(800) 853-2651
SHOP NOW

Recent content by jdetig1

Yesterday's Tractor Forums
  1. J

    20.8x38 vs.18.4x38 tires

    Well I have some bias 20.8s on my 1566 now that are about worn out. Would a 18.4 radial have about the same traction as a 20.8 bias? I would like to get some radials for a better ride. Now could I put the 18.4s on the same rims as the 20.8s or not. I believe the inside and dual rims are 18". If...
  2. J

    Dc tractor

    Did all the dc tractors have live pto? Also did they come with one way or two way hydraulics? How about the chain drive rear end it doesn't seem vey heavy duty to me did they give many problems and did you have to adjust the chains very often? Thanks
  3. J

    Case dc tractor

    I'm going to buy a dc case from my uncle that's been in the family forever. I've only worked on IH tractors so this will be a little different. What weight of oil do you use for the engine, hydraulics, and rear end? For the wet clutch if I just fill the crankcase will the oil get into the...
  4. J

    1700 chisel plow blades

    I may put some new blades on my 1700 chisel. Does anyone know what size they are supposed to be and what hole in the center for the shaft to go through. I believe it takes 24" blades and 20" on the outside and I think the shaft is square. Wheres a good place to get blades for a reasonable price...
  5. J

    Loose seal on front end spindle

    I was packing the wheel bearings on my 1566 and I took the hub off and the seal kinda just fell off the spindle. The seal is supposed to press on to the spindle tight and the new one went on pretty loose. The other side was fine. I pinged up the spot where the seal sits and put locktite on it...
  6. J

    20.8x38 tires for 1566

    Would like to find some decent used tires for my 1566. I know it's a shot in the dark but don't really want to buy new ones. Anyone have some laying around or know anyone who might? I'm located in norther IL. Thanks
  7. J

    66 series turbo

    Yeah it clears up under a heavy load. It does use a little oil maybe a quart a day working it on the chisel. Is that a normal amount of oil consumption? I thought maybe a faulty turbo was the cause of oil consumption.
  8. J

    66 series turbo

    I have a 1566 that dribbles some oil out of the exhaust manifold where the 2 pieces connect. It's not much but it's nasty and hard to clean off. What causes this? Is the correct term slobbering? Would a faulty turbo cause the oil leak or would there be oil on the intake side if the turbo was...
  9. J

    Sickle mower

    I'm lookin for an ih sickle mower I prefer a balanced head model. I would use it for a couple road ditches and some hay mowing. What would a good model be? I prefer a pull type in good working condition.
  10. J

    806 diesel torque/droop screw

    I"ve heard and read about the torque screw or droop screw. Where is it located on an 806 diesel with the roosamaster pump? I would like to turn it a little for some more low end torque. Thanks
  11. J

    Harrowgator won't lift

    Hey that makes sense that's why the old pipe that was on it didn't work either. Ill make a new one this weekend. Thanks guys
  12. J

    Harrowgator won't lift

    Ok so I need a pipe to slide into another pipe? Anyone have pictures of how it's supposed to be?
  13. J

    Harrowgator won't lift

    I bought at harrow gator that had a bent middle pipe that the hydraulic cylinder attaches to. I made a new one out of square tubing. Now the cylinder is back on but won't lift it has a john Deere cylinder. It just wants to pull or push on the hitch instead of pull or push the back tires up...
  14. J

    Farmall M brake shaft seal backwards

    I took the old brake shaft seals off my m and I really thought they were in backwards. Normal seals you would have the flat part with the brand name and number out away from the oil. I threw the old seals away but I swore the flat side was facing toward the inside of the housing where the oil...
  15. J

    Got my rear end apart on my m (pic)

    Well I tore the rear end down found 5 teeth chipped on one bull gear and teeth chipped on the pinion shaft that drives it. So I got those off eBay this morning. Took all the bearings out and all of them are perfectly fine gonna re use them. Putting new seals in and putting it back together...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top