(800) 853-2651
SHOP NOW

Recent content by jdfun

Yesterday's Tractor Forums
  1. J

    1932 D Block ???

    I believe it fit #53300 - 109900, which would be 1928 - 1930. Value ? Priceless if you need it. I really don't know the value. Tom
  2. J

    1942 JD Model B Oil Pump Drive Coupler

    I have used couplers for sale . Contact me by email or call 573 535 8952. Thanks, Tom
  3. J

    1950 mt

    Yes , the MT had two optional wide fronts. Both were round tube , one with a 48" to 68" width the other with a 68" to 88" width. I have one with the narrow wide front, however I have never see one with the wide one. As for as options I'am not positive . I have a set of shutters on mine , A belt...
  4. J

    1946 slant dash A

    I have parted out several Mid 40 A's . Give me a call, maybe I can help. 573 535 8952 . Thanks, Tom
  5. J

    John Deere B

    Sounds like the hole your digging is getting deeper and deeper. If your orginal block, rods and etc. were ok , just get the correct crankshaft. Now my sales pitch, I parted out a 1940 B (ser 89xxx) I have a crankshaft with good splines . If I can be of any help contact me be email or call 573...
  6. J

    JOHN DEERE A /60 .004 UNDER ROD BEARINGS

    I have a set of JD NOS .002 under size bearings for sale. I'll take half of what JD is asking. Thanks ,Tom. 573 535 8952
  7. J

    330 with Dual Touch-O-Matic

    I believe your 330 dual touch o matic is the same one used on 420/430S with dual touch o matic . The parts books for the 320/330S and 420/430S dual TOM's are identical. I believe if you go to 420/430 service manual you will get the information your looking for. Tom
  8. J

    need small governor part for 820

    Part No R312R fits a 70D,80,820, 720D, 730D, 840 and R. You should be able to locate one at a salvage yard. Good luck, Tom.
  9. J

    Radiator for a 39 A JD

    Yes , the side plate for a 1939 A would have a casting No A2102R. Tom
  10. J

    JD 70

    Parts book says 162.9 lbs. Tom
  11. J

    John Deere A Umbrella Bracket

    I have several umbrella brackets that are incomplete. I am looking for a source where I can obtain several caps, part #F518A, to make my umbrella brackets functional. Any help would be appreciated!
  12. J

    420/430 Power adjust wheels

    Charlie. Well are these 24" or 28"? I have a 40S and a 420S and they have 24" power adjust wheels with 6 lug bolts. Then I have a 430W and a 430T with 28" power adjust wheels with 8 lug bolts. I have a 40W with 28" pressed wheels with 9 lug bolt and a 420T with 34" pressed wheels with 9 lug...
  13. J

    Oil Filter Head on a Late B

    The filter head is made up of a base with the the oil lines attached and the upper half which has the threaded hole for oil filter bolt . Since the bolt has most likely broken out of the upper half , this may be the only part that neede to be replaced. It's still a major chore to replace . The...
  14. J

    MT motor

    I have a couple of complete motors available, also bare blocks. The 420 may fit however it has larger pistons therefore more horsepower. The mt has 4" pistons vs 4 1/4" in the 420. I'm located in S.E. Mo. For more info call 573-535 8952. Thanks, Tom.
  15. J

    320 Engine Identification

    I checked my 1958 320U and the block no is 2903 , only 4 digits. I have a pair of 1955 40w's and they both have M64T blocks with 6 digit block numbers. I noticed my 40W have the M64T cast on the block towards the back of block while 320U the cast no is toward the front of the block. So when you...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top