(800) 853-2651
SHOP NOW

Recent content by Jdtractorman123

Yesterday's Tractor Forums
  1. J

    4440 dash gauges not working??

    I checked the harness on back of instrument cluster and it is tight . Where is the main ground for the guages so I can check it?
  2. J

    4440 dash gauges not working??

    Hello I'm new to the 4440 tractors and have one that is having issues with the gauges not working. I noticed it before buying that none of them are moving. When you start this 40 series are all of the guages suppose to move all the way to the right and then back to the left when the ignition is...
  3. J

    4020 stolpher cab with A/C intermittent ??

    Thanks for the tips guys! I'll check the relays and report back.
  4. J

    4020 stolpher cab with A/C intermittent ??

    I have a 1970 4020 console with stopper cab and yes a A/C still on R12. Blows super cold but now the fan in cab quit and also the compressor stopped turning. Cut the switch off while tractor is still running and let it sit and it come son again blowing cold for less,than a minute and turns back...
  5. J

    EARLY 4020 HEADLIGHT ISSUES

    Thanks for all of the tips! I will check this week to figure it out. Are both headlights suppose to come in at the same time?
  6. J

    EARLY 4020 HEADLIGHT ISSUES

    I have a 64' gas Powershift with dual headlights on the fenders. this tractor is a one owner with approx. 2000hrs and has not been touched (wiring, or anything) with that said I know the wiring is original . I can only get the outside headlights to turn on . when they come on they are bright and...
  7. J

    4020 gas powershift how many?

    According to the serial number this is a 1964 model. I had a 1964 3020rc utility Powershift a few years ago also..
  8. J

    4020 gas powershift how many?

    I know a lot of people have asked and I haven't been able to pinpoint down how many 4020RC gas powershifts were produced the first year of production 1964. I am looking at buying one and best I can tell it was less than 100? anybody found any other research on the numbers? I hope to be able to...
  9. J

    4020 PTO seal retainer ring removed help??

    Yes I can see... lol does anyone have a picture of their snap ring pliers they use?🤔
  10. J

    4020 PTO seal retainer ring removed help??

    I have a 1972 4020 powershift that is leaking out the rear pto shaft. I have done this before but had a hardness time removing the two internal Bearing and gear snap rings...it took a lot of bloodshed and I don't want that again but I cannot seem to find what is the proper tool to buy to...
  11. J

    Wico xh TIming right? Won't start

    John, Thanks for the comments! I checked the pawls movement and they were loose and moved freely. when I tried to crank it back up after it died I noticed the pawls were not engaging.. thus it did not start back up.. I will call Jeremy today and see what they think and get it sent out for...
  12. J

    Wico xh TIming right? Won't start

    Magneto update!! I started over and removed mag and set the lag angle and backed it up from 25 degrees to 20 degrees, because when I tried to set the flywheel on the marks at left impulse compression stroke and the mag slowly moved back it would not snap til after the flywheel went 2 inches...
  13. J

    Wico xh TIming right? Won't start

    Here's something I thought of also mentioning. I don't have a gasket between the magneto and governor housing. Could that cause a grounding problem ?
  14. J

    Wico xh TIming right? Won't start

    Good comments John t. I will start over in process. Sometimes you look at things so much you about go cross eyed.. May have overlooked something..
  15. J

    Wico xh TIming right? Won't start

    Sorry, I pulled the tractor off with gator 2 feet and it cranked up.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top