(800) 853-2651
SHOP NOW

Recent content by Jeffery Rightmire

Yesterday's Tractor Forums
  1. J

    Ford 3000 and 2000 transmission rear end swap

    ok thanks
  2. J

    Ford 3000 and 2000 transmission rear end swap

    Ok thank you I will buy the correct 11" clutch disk with the correct 10 splines and use with the pressure plate that's already there. How hard is it t change ring gear on flywheel? thanks
  3. J

    Ford 3000 and 2000 transmission rear end swap

    I went out to measure for the clutch I ran into a problem the bolt pattern on the gas tractor clutch pressure plate bolting to flywheel is 3 1/2" between the bolts on triangle pressure plate with the 8 speed transmission having 10 splines. The diesel 4 speed tractor has 15 splines and has a...
  4. J

    Ford 3000 and 2000 transmission rear end swap

    Ok thanks for the replies I will give it a shot once all new parts are ordered and installed.
  5. J

    Ford 3000 and 2000 transmission rear end swap

    freeze plugs?
  6. J

    Ford 3000 and 2000 transmission rear end swap

    OK I will get a new clutch, swap the flywheels and replace the rear main seal in diesel tractor there is a little oil on back of engine also switch the top links. What about the 3 point lift draft control on side of transmission? One tractor has it the other has a blank round cap. Also bolsters...
  7. J

    Ford 3000 and 2000 transmission rear end swap

    <image src="http://forums.yesterdaystractors.com/photos/mvphoto8468.jpg"/> <image src="http://forums.yesterdaystractors.com/photos/mvphoto8469.jpg"/> <image src="http://forums.yesterdaystractors.com/photos/mvphoto8470.jpg"/> <image...
  8. J

    Ford 3000 and 2000 transmission rear end swap

    I have a 1969 ford 3000 diesel tractor C1012A with a 4 speed transmission without drawbar and non live pto. Its geared too fast for most things I use it for. I bought another 1972 Ford 2000 gas tractor B1022B with 8 speed with power steering with a 730 ford loader as a project tractor. I am...
  9. J

    Long 260 C dual clutch aligment tool

    Not sure if its a Fiat look a like, Does import tractor have a website or phone number? thanks
  10. J

    Long 260 C dual clutch aligment tool

    I am looking for a clutch algnment tool for a Long 260 C tractor with a dual clutch. The pilot bearing ID measures .670" ,and first spline is a 10 spline that measures .955" OD and the second is a 14 spline that measures 1.570" OD. Thanks
  11. J

    4000 tractor pulling

    http://www.competitiondiesel.com/forums/showthread.php?t=89074 I put a set of Mack 237 nozzles on my 3000 with a JD turbo I had a custom turbine wheel and housing made. Havn"t been to the dealer for a PTO test yet, but I can tell is deffently makes more power and EGT"s aren"t that high.
  12. J

    Long 260 C tractor split

    My step dad has a Long 260 C Diesel tractor that needs a new clutch. Does anyone have any advice on splitting a tractor like this? I have only worked on Fords and John Deere before. Thanks
  13. J

    Ford 3000 diesel TDC

    Ok I will check the flywheel access hole for tdc and if I can't find it using that method. I will pull #1 injector to find it. Thanks
  14. J

    Ford 3000 diesel TDC

    Is there a notch in the harmonic balancer for Top Dead Center for a ford 3000 diesel tractor? or what would be the best way to find TDC on #1 cylinder? Pull the valve cover and spin the engine over till both rocker arms are loose? Thanks
  15. J

    Ford 3000 Foot throttle

    This is an aftermarket setup, Made in Turkey. I bought mine about a month ago and they are up for auction all the time on ebay. I am sure someone has installed this kind before.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top