(800) 853-2651
SHOP NOW

Recent content by jeo46

Yesterday's Tractor Forums
  1. W

    Family mystery wood stove

    When my father was a child he remember playing in his grandfathers barn and seeing parts of an old stove in the early 50s but did not think much of it Fast forward 50 60 years. The home site had been sold but the old barn was still there. My wife and I wanted a barn on our land and...
  2. M

    Bull leader pliers

    What is the little appendage on the handle of the pliers used for? Thanks Mark
  3. J

    1950 Model M Saga Continues

    I had no oil to rocker arm assembly also. Machine shop had installed rear cam bushing with oil passage hole incorrectly located-I failed to notice this. Had to separate engine from bell housing, remove cam, knock out soft plug, remove bushing, reinstall bushing correctly, and reassemble. This...
  4. J

    JD 4020 Brake Pedals are loose on pivot pin

    My early JD 4020 has very loose brake pedals. How hard is it to get the brake pedal pivot pin out from the casting it is roll pinned to (R57815)? Is there room to work on this or do I have to remove the casting from the brake valve to get this job done? If so, does that cause problems for me...
  5. J

    John Deere 70 Gas in Oil

    Be sure to check part key no 7-the part has a flat side and a concave side-I think concave side goes to the upper side of sediment bulb assembly-maybe someone will verify this. When you take the body apart watch how key 7 is oriented (which side is up) and reassemble it the same way (I mark the...
  6. J

    power block sleeves ??

    Hi-My neighbor purchased a power block (for a JD 60) and two good JD G pistons (+ .125 ) and sleeved the block to G pistons for his JD 60. He has had no problems but I think he used new studs for the head. He may have used sleeves longer than the block to accommodate the oil rings and put...
  7. J

    2840 brake valve

    Tim-Can you give me your email address in case I need to contact you. I have several JD's I tried [email protected] which did not work. Thanks, Jay
  8. J

    Splitdorf 246T Magneto Magnet Recharging

    Hi-You have to have someone with a magnetism charger (a magneto shop) re-magnetize the magnet. Takes some time (1-2 days) I have heard! I think there is a schematic on this sight somewhere if you want attempt to do it yourself.
  9. J

    It will not even pop!!!!

    Compression is low, but make sure mag is timed properly-could be 180 degrees out of time. Revere wires at mag and see if it pops.
  10. J

    Farmall H battery

    Have you hooked the 6 v battery using positive ground, negative to starter? That's the way my H is. JEO
  11. J

    off topic pants

    Try Duluth Trading fire hose pants-they are tough!
  12. J

    John Deere 630 pictures.

    Nice tractor-Has lots of potential!!
  13. J

    Sodium Vapor Yard Light

    Mark-Try an LED yard light-Will save enough power to pay for itself in 3 years.
  14. J

    12.4 X 36

    Hi Butch-What do think you will be asking for 12.4 36 Firestone tires? Might be interested. thkx jeo
  15. J

    John Deere B

    John Deere gages are OK but I like Jerry Tricka's gages. His gages read oil pressure correctly and they are like originals.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top