(800) 853-2651
SHOP NOW

Recent content by Jerry Wallen

Yesterday's Tractor Forums
  1. O

    Cutting up meat what tricks do you use

    Ok so deer season is over so I can now slowly cut up the leg quarts etc into steak etc. The way I do it is thaw it just enough to be able to cut it up. Then I take a meat hammer and beat the $@%& out of it and bag it up and freeze it. Does doing it this way make it more tender then it would if I...
  2. J

    H vs. Super H??

    How can you tell the difference between an H and a Super H other than the serial tag and decal--I"m talking about physical differences. Thanks
  3. J

    1959 Massey Ferguson 40 Special

    Belt Pulley Magazine featured the 40 in the July/August 2007 issue. They have several great color pictures along with the article [email protected] is the e-mail address of the editor and they usually have back issues for sale
  4. J

    Massey Ferguson 50 question

    is 11.2X38 the correct tire size for a high arch model 50? if not what size is correct and what width wheel is standard?--Thanks Jerry
  5. J

    MF 50 information

    I noticed a picture of a 65 row crop? Did they offer this in the 50? if so where would you find the narrow front to convert? Thanks
  6. J

    IH baler decals

    does anyone know where I might find decals for a # 15 IH hay-press/baler--I am restoring one and am in need--thanks
  7. J

    help with #15 bailer decals

    does anyone know where I might find decals for a # 15 IH haypress/bailer--I realize this is mostly tractor stuff but I'm not sure where else to check thanks for any help you might offer
  8. J

    for you welder guru's

    from what I read Hansen mig welders are used a lot in body shops--the controls you are asking about may be for stitch weld timing which is a favored method of joining body panels--this is just a guess
  9. J

    ZAU brake covers

    Are the brake covers on a ZAU the same as the ones on a U? thanks
  10. J

    Drill hole in tile

    Go to Lowe's or Home Depot and get a drill bit for glass and tile--they are not expensive--They have a flat arrowhead shaped end and work great
  11. J

    Will this work on a ZAU??

    Will a generator delco remy # 1100029 also # 6661 work on a ZAU? My book calls for a #1101398 does anyone know the difference between the two? Thanks for your help Jerry
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top