(800) 853-2651
SHOP NOW

Recent content by Jesse Bergmann

Yesterday's Tractor Forums
  1. J

    1940 utu gauge/switch placement

    Would anyone on here happen to have a pic or insight showing the correct placement on a 1940 UTU. Also I will be putting an alternator and electronic ignition on it...does anyone have a wiring diagram
  2. J

    Super 66 questions

    I'm thinking about purchasing a supposed super 66...it has a super 66 belly but I'm not sure about the rest. What are the casting or serial numbers for the engine block and what is the diameter of the rear axles. please help
  3. J

    Massey Harris 44 Decals

    I'm putting decals on my 22. What are the best decals to get?
  4. J

    22 light bulbs

    Actually they are 6 inch
  5. J

    22 light bulbs

    Does anyone know what bulbs are used in the 5 inch 'guide" head lights...is there a rubber grommet that goes with them?? Btw it's a 1951 year
  6. J

    MH 22 lights

    I'm also restoring a 22. What color were the lights from the factory
  7. J

    gb diesel roosa master conversion

    How did u go way beyond it...did you make an 800 diesel??
  8. J

    gb diesel roosa master conversion

    Alright...thanks
  9. J

    gb diesel roosa master conversion

    I set it around 6 degrees btdc and turned the pump to line up the timing lines...I'll try to start it this afternoon...hopefully everything works correctly. Thanks for all the gelp
  10. J

    gb diesel roosa master conversion

    So put the flywheel on 8 degrees btdc and the pump at 4? Will the timing lines in the pump window be off a bit
  11. J

    gb diesel roosa master conversion

    So the increase in compression won't be a problem?? Have you done this conversion?
  12. J

    gb diesel roosa master conversion

    The Stanadyne pump # is DBGFCC637-2DH. The IT book says 11 degrees btdc for g705s etc...but I'm pretty sure this pump is 10% over and newer than those tractors' pumps. Plus with the increased compression I figured it should be timed differently.
  13. J

    gb diesel roosa master conversion

    I"m attempting a conversion from the bosch pump to a roosa master. I"ve already changed over the lines,drive and pump coupler. Can I still use the original fuel filter system and injectors. Also I have the original heads but a 504 bore. I"m sure the compression will be high. How many degrees...
  14. J

    roosa master pump

    I"m looking for a 6 cylinder roosa-master pump and accessory drive from a g 1000. My plan in to put them on a GB diesel. I have had the Bosch pump rebuilt but for the life of me I cannot get it to run right...timing?? Please help
  15. J

    gb diesel timing advancement

    Could someone please help me out on the timing advancement process on a gbd. It has the standard american bosch pump. I cant figure it out...thanks
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top