-
J
Updated Ford 532 injector pump question please help
Got the filter clean just didn't know there was another Inlet line. sprayed out all the powder dust and it is running again. Maine Filter was clogged with a bunch also. Do you think it could be sucking air at the banjo nut mounting? Thanks Again. -
J
Updated Ford 532 injector pump question please help
I pulled the big nut off and could not get the spring out the same hole. Thanks again -
J
Updated Ford 532 injector pump question please help
Starts to run rough after about 20 minutes. On injector pump where banjo nut enters pump, fitting spins at the two hole plate. is that okay? Also when I removed the two bolt plate, I found what looks like sawdust in there. how should I clean that out and is there a filter on the pump? If so... -
J
Ford 532 same as 4600
Starts to run rough after about 20 minutes. On injector pump where banjo nut enters injector fitting spins in two holl plate is that okay? Also when removed two whole plate found what looks like sawdust in there how should I clean that out and is there a filter on the pump? If so where is it... -
J
532 fill plug identification?
I wasable to find the drain hole in the bottom of the transmission and cleared it.also found the mushroom looking thing beside the shifters was a transmission dipstick.I was able to tighting leaking screw up and it stopped the leak. Glad I didn't take the screw out! hydraulic oil was about 6... -
J
532 fill plug identification?
I have attached a picture of a plugs 1 half inch 1-3/8 and one quarter inch on the 532 that I would like to identify and more importantly a vent hole or breather that is leaking oil out and probably water in at the end of the pen you will see it. Thanks. -
J
transmission oil leak 532 or 4600
I did not see a hole with a cotter pin in it.the j channel is bolted to the mounting bolts on the bottom of the transmiss to hold a loader. is it ok to leak it that much oil? -
J
transmission oil leak 532 or 4600
thanks for the info. was wondering how you think it got in there and how I couldn't stop a water from getting in there again. Also somebody told me I should use 90 weight gear oil? what is 134 D and how much does it hold? have a great day.! -
J
transmission oil leak 532 or 4600
I have a transmission leak between the engine and transmission.It has a green tent and foamy somewhat.I drain the transmission oil and it is definitely from there no water in the bottom.wondering how much that is supposed to hold and how do you tell when it is full?any ideas where the leak may... -
J
532 or 4600 loader question
can I not use the same pump thats on the tractor? And that reservoir as well? -
J
532 or 4600 loader question
On a 532 was looking into putting a loader on this tractor. Wondered if there would be any problems.Would it operate right fast enough ect. It does have power steering.The loader is off a case 630. thanks Jim -
J
New pictures need help Ford 532
Thanks for the information top right may well be speed control for the auxiliary. I don't think the guy I got it from knew it was on there he said the auxiliary cylinder always ran real slow.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy