-
J
600 series lift cover with 2000/3000 cylinder
I posted on the Fordson forum. “Major man” suggested I post on the Ford forum. He says I have a cylinder assembly from a 2000 or 3000. -
J
Lift cover linkage adjustment External spool spring
All the procedures for adjusting the position a draft linkages are for a cylinder that has an internal spring on the control valve. The spring on mine is external. Procedure for the internal type requires that you slip a gauge between the spool and the cylinder face. The external spring won’t... -
J
600 series lift cover with 2000/3000 cylinder
Yep, you’re right I found photos of a Dexta cover. Now I’ll post on the Fordson side and find the procedure there. Thanks Shaun! -
J
600 series lift cover with 2000/3000 cylinder
That sounds reasonable. I wonder how your supposed to measure the gap between the spool and the body. The spring’s in the way. Last time I eyeballed it with a caliper. -
J
600 series lift cover with 2000/3000 cylinder
Hmm, sounds familiar. My dad fill the crankcase with water. It was a Ford 4000. The filler caps for the radiator and crankcase are identical. My hydraulic case oil is UTF as required though. -
J
What’s this pin for?
1957 641. 3/8” dowel pin on: LEVER; Assy., Hydraulic Lift Hand Control Should it be attached to something? -
J
600 series lift cover with 2000/3000 cylinder
I’m in the process of making lift cover adjustments on my 1957 641. Lift operates great and holds perfectly. It has limited function on the lever at quadrant. Only the upper two inches allow lift, the rest is all down. Years ago, I replaced the cam follower and attempted the position... -
J
640 front axle support bushing
I used a pc of 1/2" all thread, nuts, washer, flat bar and a 15/16" socket to "press in" steering sector shaft bushings yesterday. Worked like a charm! Will use same type set up larger axle bushing soon. Shade tree mechanicing! -
J
640 front axle support bushing
Ordered split bushing pt #2N3039 from Ebay received a solid type. The split bushing had a brass looking coating inside. The solid bushing had no coating. Is one better than the other or easier to install? Thanks -
J
A better fuel shut off valve?
When the buna fails, try Viton orings from McMaster Carr -
J
A better fuel shut off valve?
I have a solution for you if your tank has a plugged 3/8" NPT hole in the right rear corner of the tank on the bottom. My replacement tank did. -
J
Lift control travel
Dean, if I felt the need to tear into the lift, what would I adjust to expand the range of the touch control lever? The control valve turnbuckle or the control arm rod?
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy