(800) 853-2651
SHOP NOW

Recent content by jkc42

Yesterday's Tractor Forums
  1. J

    jd 336 baler knife need sharpening

    I have the OM but no where does it tell me how to sharpen the knife. My plunger knife needs to be sharpened, can anybody walk me through the process. Thanks for your help
  2. J

    jd 2355 loader help

    Wow, thanks for all the help. Just wanted to mention that the 2355 is an open air tractor. I apreciate all the help. Jody
  3. J

    jd 2355 loader help

    My 2355 came with a Allied loader but it has seen way better days. What would be a good loader for this tractor. I would like a quick detached loader so I don't have to drive the field with it on all the time. Thankls for your help.
  4. J

    JD 2355 tool box location

    It does have a loader attached. Anybody got a photo of the way they did it?? Jody
  5. J

    JD 2355 tool box location

    Just purchased a 2355 open air unit and was wondering if anybody had installed a tool box on their unit. If so can you give me a reply and let me know where you place it. I can"t seem to find a spot. Thanks for you help
  6. J

    mf35 and rough cut mower

    I have a mf35 3 cyl perkins. I am thinking about purchasing a Landpride RCR 1872 rough cut mower for it. It is the 6" model and spec shows 20-50 hp required. Does anybody out there have anything similiar? Will there be issues with my tractor and the mower? All comments appreciated.
  7. J

    MF35 3ph stablizer question

    The bolts are long enough to put the brackets on but I am unable to get the pin into the front hole due to the metal guset from the FEL. If I use the rear hole I will need a bar 28" long the kit I have has a 31 1/2" bar. Any other suggestions??
  8. J

    MF35 3ph stablizer question

    Thanks for the reply. I was hoping there would be an easier way. I was thinking about drilling the guset plate and putting the pins there but really not sure. Anybody else have this problem??
  9. J

    Installing a fuel gauge on a MF35

    Thanks for the reply. Just wondering if there was an after market guage that could be hooked up without to much bother.
  10. J

    MF35 3ph stablizer question

    I purchased the stablizer kit for my MF35 tractor but because it has a loader installed the kit will not bolt on. Any suggestions? Thanks
  11. J

    Installing a fuel gauge on a MF35

    Can a fuel guage be installed on a MF35? If so what to buy, how hard to install? Anybody out there done that?
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top