(800) 853-2651
SHOP NOW

Recent content by John4780

Yesterday's Tractor Forums
  1. R

    Farmall Cub Sickle mower Pittman Arm

    Hi, Can someone tell me if I am missing a piece for this Pittman assembly. I cannot get this to stay attached when I engage the PTO. It seems as if I need something to make the spring functional and put pressure on the latch. Up till now I just had the spring arm going into the hole at end...
  2. B

    Paint colors for Oliver, Moline, IH plows

    I have caught the plow bug a few years ago. And after Grandpa has passed away last fall I inherited some more plows. An Oliver plowmaster 100 (red frame green wheels on rubber), Servis terrace plow (An IH little Genius plow with an auger on the back) and 2 MM plows one is a 4 bottom round tube...
  3. J

    24 T baler problem

    I have the manual and set everything up according to it. The wiper arm sweeps past the bill hook. Is the bill hook supposed to be close to the wiper arm? The wiper arm has a little play in it. Does it need to be shimmed? I don't remember reading about using a feeler gauge. I put new knife blades...
  4. J

    24 T baler problem

    Right side knotter ties about every two bales and then wont tie for about every 6-8 bales.Sometimes the twine will break every 10-12 bales and have to re-thread the needle, and then the thing will tie about every two bales and go through the same routine. Have changed the needle twice, adjusted...
  5. J

    24 T knotter not tying

    Thanks for the info guys. It will all help in trying to solve this problem. I put two new rolls of twine from John Deere in the baler last year. I did notice some pieces of thin twine on a few bales and wonder if the twine is bad. Installed new knife blades last year and rebuilt both knotters. I...
  6. J

    24 T knotter not tying

    The knotter on the right side (inside) will tie for about 3-5 bales and then not tie for the next 3-4 bales. Most of the time it will tie a partial knot and the string will slip out of the knotter and be under the bales in the bale chute. I have timed the baler according to the book and...
  7. J

    3 point wont move

    Thanks for the help. I got ready to tear into the thing and started the tractor to move it. I raised the lever for the 3 point and it lifted and lowered. I played with it laqst night and it works great. I"m thinking maybe it had an air pocket in the piston for a minute.
  8. J

    3 point wont move

    I had a problem with thye 3 point on an 8n not wanting to work right. I replaced the top cover (under the seat) and the thing worked great. I have a cement weight on hte 3 point right now and it worked good up until today. Now it won"t raise or lower. I moved the small lever under the seat and...
  9. J

    Won't tie on 24 T bailer

    Thanks guys, I checked the knotters again today and found that the twine disk is not turning like it is supposed to. I took the worm gear shaft out and tried to turn the twine gear with a pair of pliers. it turns almost all the way and then catches like it has to be forced to turn. This is...
  10. J

    Won't tie on 24 T bailer

    I had to replace the needle frame and one of the needles because I broke both needles and the Deere dealer said they were bent after I welded them. The needle on the left side is the welded one and the knotter ties like it is supposed to. The needle on the right side has been replaced with a...
  11. J

    450 clutch adjustment

    Thanks for the help. I kinda figured something was missing. Those washers must have fell out when I slid the throw out bearing off the shaft. I saw the washers in amungst all the gunkie crap I scraped out of the bell housing. Thanks again.
  12. J

    450 clutch adjustment

    I pulled the engine on my Farmall 450 gas before winter and had to replace the throw out bearing. I just put the enjine back into the tractor and hooked the clutch arm back up and now I can"t put the tractor in gear. I tried to adjust the clutch arm and that didn"t work. Did I maybe not get the...
  13. J

    How do I take this out???

    That worked great!! Thanks for the help.
  14. J

    How do I take this out???

    The throw out bearing in my 450 gas Farmall is shot. I took the engine out and am trying to figure out how to get the bearing out. I disconnected the clutch peddle rod and the connecting rod for the TA. I need to know how to get the bracket off the shaft for the throw out bearing so I can...
  15. J

    Rear crank seal

    Ok, thanks. That seams like an odd way to put the retainer on
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top