(800) 853-2651
SHOP NOW

Recent content by johnahowell

Yesterday's Tractor Forums
  1. J

    4400/4500 bolster removal

    Did you swap any hydraulic pumps also?
  2. J

    4400/4500 bolster removal

    Very nice! Almost exactly what I want to do. I need to either switch the front axles or rebuild the 4500 axle. The king pins are seized and again, I don't know how to remove them.
  3. J

    4400/4500 bolster removal

    I've measured everything and yes, I need to swap the radiator frame also which is why I need to swap bolsters. The 4500 radiator frame does not mount to the 4400 bolster. The loader attached to mounting spots on the engine and the rear axle. Everything matches perfectly for sizes. No backhoe is...
  4. J

    4400/4500 bolster removal

    Hey everybody, I'm very new to working on tractors. I have both a 1970s 4400 and 4500. I'm trying to move the loader from the 4500 to the 4400. In order to do that, I need to swap the bolsters. What I need help with is how to remove the pivot pin connecting the bolster to the front end. It may...
  5. J

    Ford 4500 cab and loader removal

    This is the picture before I try the strap to keep the cab supports together and not as flexible.
  6. J

    Ford 4500 cab and loader removal

    I'm using a chain fall and I've already set it up on the cab. Now I'm having to put a strap on the cab supports because they are flexing too much when I drive the pin out. But at least the pins are free inside the loader frame and loader arms now. Been a fun day with only one trip to harbor...
  7. J

    Ford 4500 cab and loader removal

    Thank you very much, if you have any advice on removing the loader and cab I would sure appreciate it. I'll be hopefully working on it all day tomorrow
  8. J

    Ford 4500 cab and loader removal

    Does the same pin go through the frame the loader arm and the cab up right?
  9. J

    Ford 4500 cab and loader removal

    I need advice on how to remove the cab and loader from my 1970 4500. I've read in places that the pins should be driven from the inside toward the outside. This confuses me because the cab post is on the outside of the loader loader arm and to remove the cab, I would need to also remove the...
  10. J

    IH 383, worth it?

    Yes, the one I am looking at is from Japan with the Nissan motor. There is some documentation that it may have been at an Ag show in 1981 in Iowa. I don't know where to look for a current value though
  11. J

    IH 383, worth it?

    I'm looking at an IH 383 2WD. It is in good shape as far as I know, the previous owner, my late uncle, took good care of it treated it like a show tractor. After sitting dormant for 3 years, it started right up and sounded great. I have no idea what thee tractor is worth or if parts are readily...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top