(800) 853-2651
SHOP NOW

Recent content by JohnMoore

Yesterday's Tractor Forums
  1. J

    case 530 grinding starter

    not a clean spot on ring gear, just to get teeth to align with starting gear. slow to turn over, finally started messing with clutch and levers. transmission was in neutral and pto disengaged, but the lever on right side was forward, i moved it back and forth, found a niche in the center and...
  2. J

    case 530 grinding starter

    New starter on, had to move flywheel just a bump...turns over great. Waiting on a oil pan, and oil filter mount bracket gasket to reassemble and fill with good oil, new plugs,wires,etc on...I'm anxious to hear her run...FYI..John Saeli has all hard to find and obsolete parts at great prices..met...
  3. J

    case 530 grinding starter

    Update---they shimmed the shaft so it doesn't move, Bendix engaged once and turned engine over..yay...but started grinding again on subsequent tries. Bench tested it and Bendix sometimes doesn't go out far enough and others it doesn't retract back in...I'm frustrated and just ordered a new...
  4. J

    case 530 grinding starter

    Update---they shimmed the shaft so it doesn't move, Bendix engaged once and turned engine over..yay...but started grinding again on subsequent tries. Bench tested it and Bendix sometimes doesn't go out far enough and others it doesn't retract back in...I'm frustrated and just ordered a new...
  5. J

    530 parts question

    Yes that's it, I need the gasket in that picture. That also narrows down the year model tractor it is. I just inherited this tractor, trying to get her going. I see no numbers on dash panel to track, entire gauge cluster is gone. Where can I get that gasket and oil pan gasket? Thank you
  6. J

    530 parts question

    Gas engine, took oil filter off also the bracket that oil filter screws onto that bolts to side of engine. What is its name? I need a new gasket and cant find one, also, can you replace oil pan gasket by just dropping it till it hits mounts? unable to take rear mount and front end loose at this...
  7. J

    case 530 grinding starter

    I looked up some ring gears that had to be replaced....wow...mine doesn't look anything like those, not worn to bad at all in comparison....I will take starter back to be adjusted for that shaft movement and manually turn flywheel to a smooth area and put starter in and see how it goes
  8. J

    case 530 grinding starter

    O no, that may be true, I turned the flywheel by hand all the way around, two areas I seen had some teeth that had some wear on the facing side, approx 4-6 teeth each spot. How hard to split the tractor? Couple jacks, concrete blocks and big wrench??
  9. J

    case 530 grinding starter

    :lol:
  10. J

    case 530 grinding starter

    Just noticed the shaft the Bendix drive slides on also slides, while engaging the starter I noticed the gear only moved up about eighth inch but I can move it and the shaft another eighth or so by hand, that may be the problem, as if they failed to replace a washer to the seat of the shaft...
  11. J

    case 530 grinding starter

    Thank you for responding, I took it off and engaged it with jumper cables before, all was good, but someone suggested that it needed rebuilt, just to have new parts installed and cleaned up, so I just got it back from the shop that rebuilt it(they specialize in farm and industrial starters) and...
  12. J

    case 530 grinding starter

    I don't get it, it is the same starter that has been on it...my uncle used this tractor last year. I helped him with fuel filter. He parked it and covered it with tarp, he passed away about 8 months later and here we are :D ...any other ideas, please??
  13. J

    case 530 grinding starter

    Help,I just inherited a case 530 tractor that did not run,it did run last spring. had the starter rebuild because it was grinding and would not turn over, got it back today put it all together, and it is still grinding, I took a flat bar and the flywheel does turn over, teeth look fine, any ideas??
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top