(800) 853-2651
SHOP NOW

Recent content by johnsonh93

Yesterday's Tractor Forums
  1. J

    Farmall 560 head gasket frustration

    i talked to the machine shop, and at the point we were at he recommended doing the head, first, and then look into going deeper. I took a compression test and all cylinders were over 100, but i believe they are supposed to be quite a bit higher. However, ive heard of motors running on less...
  2. J

    Farmall 560 head gasket frustration

    do you know if there were more than one option for head gasket? got the gasket through Steiner's
  3. J

    Farmall 560 head gasket frustration

    I have a Farmall 560 gas that I recently tore into due to it fouling plugs. Found multiple issues. Ended up sending the head in to the machine shop after first head gasket attempt failed. I installed the head- all new gaskets, torqued to spec, etc.- I ran it up to temp, retorqued head bolts...
  4. J

    John Deere 1250 finger pickup

    After reading the book I have, I apparently had passed over the page that talked about the soybean cups. I believe I found the correct pages If I'm not mistaken, you pop the seed box off, and turn the plate on the underside, closing the path to the fingers, and diverting it to the "cups". One...
  5. J

    John Deere 1250 finger pickup

    Will a 1250 with finger pickup plant soybeans? What do I need to do to make it possible? Couldn't really find a solid answer on Google.
  6. J

    Field Navigation Apps

    The gps on your phone won't be good enough to be consistent. I use an app to map my fields, just to give me a rough idea what I have, and you could do the same field back to back times and you'd get a slightly different boundary. In order to do a good job, especially with the auto steer, where...
  7. J

    NH 469 Lower Roll bearing replacement

    It was held on with a gib key, hence what seems to be the root of why it wasn't coming off lol...no room to get a punch behind it, and no gib key tool either
  8. J

    NH 469 Lower Roll bearing replacement

    Got it off. Got mad and went to Tractor Supply and got the biggest puller they had, along with a hand held propane torch. Heated it for a few minutes, got the puller on, grabbed my Milwaukee impact set it on high, and after a couple minutes of hiding my face and running the impact she finally...
  9. J

    NH 469 Lower Roll bearing replacement

    then again, the manual for the 488 doesn't even bring up a key, so possible that they excluded the set screw
  10. J

    NH 469 Lower Roll bearing replacement

    The parts manual does not bring up a set screw. All I can see is the key Doesn't make sense, but you'd think it would be in the book if it was there?
  11. J

    NH 469 Lower Roll bearing replacement

    I am attempting to replace the bearing for the lower roll on the LH side. In order to get to the bearing there was the drive sprocket to remove that drives the roll. After removing that, there was a plate behind that (which the sprocket was bolted to) that needs removed as well. I attempted to...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top