(800) 853-2651
SHOP NOW

Recent content by Jon Pedigo

  1. S

    coverting to 12 volt

    Will converting a Ford Jubilee to a 12-volt lower the value of it?
  2. 2

    #410398 open fanshaft A oil issue

    Had a customer call me last week about his A starting and running for about 15 minutes and shutting off. Thought most likely it’s a coil and I’ll come diagnose it to be sure. Got there and it started right up. The red head oil pressure indicator never moved. Shut it down and hook a gauge into...
  3. Ultradog MN

    Re: ford tractors

    "The thread you posted to is over a year old and has nothing to do with your question. You should have created a new thread to ask your question. More than half of the people on this board use classic view and so it won't even show up on their font page and will be buried so many pages...
  4. M

    Loose Crankshaft and pulley splines

    Is there a way to fix the splines on a crankshaft pulley? The crankshaft pulley is loose, as well as the flat head or slotted bolt that holds it in place. Yet, the pulley itself and possibly the crank splines are not a tight fit. About a 1/32? of play when I slip the pulley on to the...
  5. kcm.MN

    Which fuel line would you recommend?

    I have a 12v fuel pump (approved for gasoline use) and I want to use tubing so I don't have to lift 5-gal cans up to the tractor. Also, when I'm busy elsewhere, wife can't lift the gas cans to refill the riding mower. I have a choice of 5/16" PVC fuel line (clear), or 5/16" polyurethane fuel...
  6. K

    3000 Ford

    I am going to do a compression check on a 3000 ford tractor.(3 Cylinder Diesel) How much psi should I see on each cylinder to consider it good and how much difference between cylinders is acceptable. Thanks
  7. K

    4020 shifter cam wear

    Overhauling trans in 4020 Has synchro Noticed the shifter cam had a slight groove on it looked at some images online just to compare and they looked about the same for wear, what is consider normal wear on these cams and how much is too much, one guy told me if the hole has been worn into...
  8. T

    IH 454 backfiring though the carburator.

    My 454 runs fine at low idle and it runs fine at high idle as soon as I put it under load it backfires through the carburator, everything is new plugs wires everything.
  9. J

    Me 180

    I just bought a mf180 trying get info on serial number 9A 41071 can't find much would like more help please yr etc thanks
  10. E

    100% MADE IN USA floor jack?

    I have been able to determine that US Jack products are indeed 100% US made, no "Assembled in USA" crap. Are there any other US manufacturers of floor jacks? The 4 ton US Jack floor jack is $1400, that's about double what I can afford.
  11. B

    Hay Preservative Applicator Set-Up

    Posted a similar post on another forum, thought some might find it helpful here too.... As I mentioned in the 2017 photos thread, I lied. Weakened by potential hay sales lost due to not cutting, I made a second cut on my Timothy mixed grass hay field. Have had a buffered propionic acid...
  12. J

    Source for Remanufactered Ventilator Pump

    I took off the housing to replace the gasket around it, slid the housing back on and turned the tractor on and it tore apart the paddle wheel. I obviously bumped the paddle wheel unknowingly while putting the housing on. Hence was not a good day.
  13. J

    Source for Remanufactered Ventilator Pump

    Had the ventilator pump go out on my 66' gas 4020. Im looking for a remanufactured one from someone who has a good history or has been reliable, I'm out of central Indiana. Been looking on the inter web for one and haven't had much luck
  14. J

    Engine swap in 4020

    Gas around me (central Indiana) have been going for around 6-8k and you cant buy a diesel for under 10k, that is if you want it to look halfway decent, add in the powershift and side console models and you cant buy em for under 12k where im at
  15. J

    Engine swap in 4020

    Bought a 4020 a little while back at an auction for a good price, only issue is that its a gas. I was curious to see what it would take to do a swap to a diesel. I had been looking for a diesel but coudnt pass up this tractor with how high diesel 4020's are going now-a-days 1.) How hard is it...
See more
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top