(800) 853-2651
SHOP NOW

Recent content by Joseph Harvey

Yesterday's Tractor Forums
  1. C

    Best RELIABLEdiesel compression tester?

    So I spent $160 Canadian on Performance Tool diesel compression tester and it worked on first cylinder glow plug hole and then the air release button guts stayed in the release position. I was 3 hours drive out in the bush yesterday and didn t have a thin enough 8 mm wrench to disassemble it...
  2. G

    Picture Of The Day

    This tribute car was spotless! 427 4 speeds with black interior. It is Daytona yellow. $89.000 Guido.
  3. R

    Resistor

    What is the difference between a A8NN-12250-A and A8NN12250-B resistor? Sites say both fit a 9N
  4. L

    3 wire gm alternator

    I read in wiring one up to either use a charge light or a diode. Am I reading right? I don't understand, a diode lets current pass only one way and a light bulb will let current pass either way. Why will a light bulb work and if it will why have anything there?
  5. A

    John Deere 70 gas - need flywheel starter ring gear

    I ordered a new flywheel ring gear. It was sent but a John Deere model B ring gear got pulled off of the shelf. Sent it back yesterday. Parts company does not have a ring gear for a John Deere 70 gas in stock - back ordered. It is the same as a John Deere 720 and 730 gas. Anyone have a ring...
  6. F

    Ford 3000 gas engine won't stay started

    New Member My 3000 will start right off but as soon as the key switch is released from the start position to the run position it shuts off. If left in the start position it continues to crank and run. I removed the sediment bowl and cleaned it and the filter, there was gas there and it starts...
  7. Ande

    Any of you have some you havent done much with

    The "900" is still sitting in the meadow, havent had a chance to put some rod bearing in her. The "SC" became a donor to my other "SC" which save a bunch of doe. The "VA" is in storage, and planned to get her running this summer, and use it for odd jobs.
  8. S

    Rust removal with muriatic acid

    I made some handles, door stops, hinges, and other miscellaneous hardware out of mild steel for the doors of a shed last year, but a different problem prevented me from being able to install them. Sitting in my unheated garage they got rusty over the winter. Doing a different project I noticed...
  9. 5

    Electrical gurus

    I posted on Allis Chalmers forum about a WC voltage regulator. Would much appreciate a look-see there from my electrical guru friends. Thanks to all responders.
  10. R

    Correct governor installation on NAA??

    The governor worked fine before I did major engine work. When reinstalling the governor does the fork have to be aligned or not when reassembling the front cover on the engine? The engine does not hold speed when load applied as in engaging PTO or going up slight inclines, etc. Have tried to...
  11. C

    430 Hood Decal Placement

    Hi all, Am putting some decals on my 430 S tractor hood and just wanted some advice on where the number and John Deere should end up on the hood in relation to the top of the yellow and where to center it. Thanks Chuck
  12. F

    770 Seat Rebuild

    I'm looking to rebuild the seat assembly on my Oliver 770. I'm having issues and am looking for advice or direction on the following items: 1) My main issue is removing the two u-shaped bars that have one end pass through the seat springs and the other end pass through a bracket that...
  13. D

    Fuel in oil

    Yes I have a d-239 544 international and I'm getting fuel in my oil. So I changed the front lip seal on Bosch injector pump.(BC I read on this site its most likely was that) but changed seal ran for 20 minutes and crankcase is full of fuel again.... Any other suggestions?
  14. A

    Dan White

    Does anyone out there have the contact information Dan White (the fellow with the case parts)? Thank you.
  15. D

    BF AVERY

    Help I have a model 5 bf avery and I need a complete motor. When I got this tractor it has a V4 wisconson on it now it is froze up and I dont really care Does any one out here in YT have a complete motor and if so what do you want for it Also I live 80 miles northwest of Spokane Wa Thanks Dale
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top