(800) 853-2651
SHOP NOW

Recent content by Josh8906

Yesterday's Tractor Forums
  1. J

    Brushwhacker Skid Steer Cutter

    I did find out a little more information. This is the same company as Brushmonster out of Alabama. Apparently, they changed their name awhile back.
  2. J

    Brushwhacker Skid Steer Cutter

    Does anybody know anything about a 5 foot skid steer cutter named Brushwhacker? I'm trying to see if it is a good cutter to purchase. It has Brushwhacker.com and a phone number (888-547-7950) on it but neither one works now. It is the color yellow similar to bushwhacker.
  3. J

    Vicon CM2400 Mower

    I have the spring pretty much bottomed out. I'm not sure about the catch I will have to look and see if it's rounded. Thank you!
  4. J

    Vicon CM2400 Mower

    Hi! My breakaway bar keeps slipping when I am mowing. I've took pressure off the spring and retightened it but it still slips as soon as I pull off. Any ideas or should I replace it? Thank you!
  5. J

    Vicon CM2400 Hay Mower

    I am replacing the bearings in one of the cutter heads on a Vicon CM2400. When I press the hub back on to align the holes for the roll pins I cannot turn the gear by hand. It seems like there is to much pressure on the bearings. If I back off the hub some I can turn it by hand but the holes...
  6. J

    Bushhog 2615 Transfer Gearbox Seal Bearing

    I have an output shaft on my bushhog 2615 transfer gearbox that has a leaking seal and a little up and down play. Does the top cover of the gearbox need to come off to replace the outer bearing and seal or can this be done from the shaft end? Thanks for any help?
  7. J

    Bushho 2615

    I just purchased a older used Bushhog 2615 and wanted to replace the oil in the power divider gearbox. Does anybody know how much oil it holds and the type? I believe on the cutter gearboxes it's 6 quarts of 80w90 but wasn't sure on the power divider gearbox. Thank you!
  8. J

    Massey Ferguson 165

    Hi, I was wanting to install a block heater on a MF 165 with the ad4203 diesel. On the left side of engine there is a plug in the center with a small threaded plug located in the center of it and towards the back of the engine on the left side there is a freeze plug. In the attached photo...
  9. J

    John Deere 4230 PTO Detente Lever Broken

    I removed the roll pins and the arms on the outside of cover and still the inner cover won't come off. I even tapped on those shafts that the roll pins come out of and the inner cover still won't budge. The only thing I can think of is it must be really stuck together with the gasket but seems...
  10. J

    John Deere 4230 PTO Detente Lever Broken

    Hi, I have my PTO Clutch cover off tractor to replace the PTO Detente Lever arm that has broken. I have been tieing up PTO lever with bungee cord for awhile and decided to fix the issue today. While I have the main cover off the tractor I cannot remove the small cover that is bolted onto...
  11. J

    Stanadyne DM4 John Deere 4230

    I have a Stanadyne DM4 injector pump that may be leaking fuel into oil on my John Deere 4230. I've already replaced the lift pump. I was wondering how hard it is to replace seals on this pump? I found a seal kit for $30 but didn't know if this could be something accomplished at home or if it...
  12. J

    1977 John Deere 4230 Fuel in Oil

    When I remove the injection pump to replace the seals how do I line up the scribe marks at top dead center? Also should I go ahead and install new injectors or have the old ones cleaned? Thanks for the help!
  13. J

    1977 John Deere 4230 Fuel in Oil

    When I remove the injection pump to replace the seals how do I line up the scribe marks at top dead center? Also should I go ahead and install new injectors or have the old ones cleaned? Thanks for the help!
  14. J

    1977 John Deere 4230 Fuel in Oil

    I have a 1977 John Deere 4230 that is still getting fuel into oil with a new fuel lift pump installed. The engine always had a little white smoke but I noticed it is smoking a lot more than usual especially at low idle and when the engine idles up. It even sounds like the engine may be missing...
  15. J

    John Deere 4230 Rattle Noise

    After using the tractor some more I noticed it is smoking white smoke more than usual. It has always done it a little since I had it but not as much as it is now. It is also idling a little lower at around 600 rpms where as it use to be around 800 to 900 rpms. Could the knocking noise be from a...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top