(800) 853-2651
SHOP NOW

Recent content by Jpd83Jpd83

Yesterday's Tractor Forums
  1. J

    Stuck Pin on replacement part - JD Front Support

    Thank you for the replies. You are right, the pin is pressed into place. I was able to pull it out and get the new pin installed. In my old front support, the casing was cracked and the pin just slide out, so I did not know it was press into place before the casing cracked. I now have a...
  2. J

    Stuck Pin on replacement part - JD Front Support

    Any ideas how to get a stuck pin unstuck off a jd2040. I am in the process of replacing the Front Support that hold the pivot axle. The one that was on my JD2040 was cracked. I found a good, inexpensive replacement part for the same money. I was able to replace the bushing in the front...
  3. J

    Welding on John Deere 2040 frame - front support

    Thank you for the reply! Can you explain a little more about the 1/4 inch plate? Size? Length?
  4. J

    Welding on John Deere 2040 frame - front support

    Fortunately or Unfortunately - I do not see any welds on the entire tractor - had it for 5 years or so. Great running tractor.
  5. J

    Welding on John Deere 2040 frame - front support

    It seemed to be more granular, so this confuses me even more. I was convinced it was cast steel.
  6. J

    Welding on John Deere 2040 frame - front support

    Yes - I have called John Deere , and no one there seems to know what kind of alloy was used for this part.
  7. J

    Welding on John Deere 2040 frame - front support

  8. J

    Welding on John Deere 2040 frame - front support

    Does anyone know what kind of metal/alloy used for JD 2040? What is the best welding rod? Cast Low Alloy steel? or maybe Cast High Alloy Steel? or Cast Iron? Jimmy
  9. J

    Points and Openers vs Middle Buster Plow

    Thanks for the comments - E.B.Haymakin - I was going to try to run the middle buster very shallow. You have got me thinking I may need to go back to using a disk furrow plow. To be honest, I used my plow wrong the first time. I had the disk set on an angle, and it moved to much dirt...
  10. J

    Points and Openers vs Middle Buster Plow

    Thank you all for your responses, especially BarnyardEngineering! I am planting Bermuda Sprigs(basically the roots of bermuda grass that has had the dirt removed). The Bermuda King Sprigger plants 2 or more rows of sprigs at one pass. The box above holds several bushells of bermuda...
  11. J

    Points and Openers vs Middle Buster Plow

    Can someone tell me the difference between using a point with opener like on a bermuda king sprigger vs using a middle buster plow? I am considering using my middle buster plow to create a furrow, then hand putting the sprigs in the furrow, and then using something to fill the furrow back up...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top