(800) 853-2651
SHOP NOW

Recent content by Judson Marvin

Yesterday's Tractor Forums
  1. J

    57-59 td9 hydraulic pump

    Hello. I have recently purchased a really nice 57-59 td9 1550 rpm dozer. I am wanting to fab up a bracket so that I can install a tilt cylinder on the blade. My question is does anyone know of the gpm the hydraulic pump puts out so I can size my spool valve accordingly? All the research I?ve...
  2. J

    White 5100 planter

    Hello. Has anyone swapped out the hydraulic blower motor on a white planter for an electric motor? If so what motor did you use and where did you purchase it. Thanks
  3. J

    Tranny question

    I'll take a pic tonight and post iT.
  4. J

    Ford 641 trouble

    Sorry yes lift cover. You can take the side cover off where the pto selector is and look inside. No pin in the coupling. You'd have to split the tractor to take apart and put back together. You could also jack the tractor up and spin the wheels see if you can pin point where noise is coming from...
  5. J

    Ford 641 trouble

    I'd take top cover off. You'll be able to see the coupler and diff to see what is broken. Could be axle too
  6. J

    new hollen 555l skid steer will not move no hy

    Either your pump is shot or if that's a direct drive could have steered bolts or shaft. Have to pull cab To have a look see what's going on
  7. J

    Tranny question

    I have the dual clutch and the flywheel. I know I'm gonna need those. I was just curious if I could put a single stage clutch on it. The dual clutch was wearing on the collar that goes around the tranny shaft. Do you know what that would be from? Riding the clutch?
  8. J

    Tranny question

    I have the trans to axle coupler. But I'd have to get a pto shaft. Which won't be hard. These couple guys with bone yards close to me. I'm assuming that the trans will work with a single stage clutch?
  9. J

    Tranny question

    Hello all I'm looking at a Ford 4000 industrial four-cylinder gas that has a select o speed that couple the gears are shot my question is I have a five speed transmission out of an 861 will that bolt right up and also could I put just a single stage clutch on it instead of the dual stage...
  10. J

    Ford 4000 industrial cable power steering

    How do I contact him
  11. J

    Ford 4000 industrial cable power steering

    Hello all. I have a 4000 industrial that has the cable power steering. It turns good and the cable doesn't slip. But when I turn to the left it appears to over steer and when I turn to the right it only turns about half way. Is there a way to adjust the cable? I took the side cover off the gear...
  12. J

    Ford 4000 industrial

    Yes sorry I'm a bone head. Yes it's a 4 cylinder and The pump is on the right. My mind must have been thinking backwards. Anyway. Thank you for info
  13. J

    Ford 4000 industrial

    Hello. I have a ford 4000 industrial that has the vane style hydraulic pump mounted on left side of the motor. Can anyone point me in right direction as far as where or part numbers for the 2 o ring gaskets that go between the transmission and the hydraulic manifold? Thanks for the help
  14. J

    Ford 4000 industrial

    Thanks. I"m just gonna go with the stock clutch. Just figured since I have to replace clutch anyway I"d ask the question
  15. J

    Ford 4000 industrial

    I have a 4 cylinder 172 cubic inch motor. I have not split the tractor yet to compare parts to the 861 I have. But inside. The hydraulic reservoir where the pto connects is all the same.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top