(800) 853-2651
SHOP NOW

Recent content by jvmopar

Yesterday's Tractor Forums
  1. J

    final drive seals for AC HD 10 dozer

    What's the numbers you have for your seals that you need?
  2. J

    cat d7 headgasket

    Here are gasket sources for 1F9679 http://www.machinerytrader.com/list/partsSearch.aspx?PCID=&dlr=&GUID=7b270c2541954891ad1c07449454b78d&Manu=&Mdltxt=&mdlx=Contains&PartNum=1f9679&btnPartSearch=Search&PST=Starts&fullsearch= And for 1S9397...
  3. J

    Front Idlers wear

    Sounds to me like you either need the pins and bushings either turned if they can be or replaced. Taking a link out isn't the proper repair. As the pins and bushings wear the chain pitch changes, this will cause the chains to bind on the sprocket causing excessive wear there.
  4. J

    hay combustion

    I always worry about mine too. I'm no farmer, kinda got thrown into it after my wifes grandfather died. But I've put some bales in the loft that I thought were too wet. 2 bales out of 1000 were a little moldy. I was told by the old farmer down the road to stack "damp" bales on their end in the...
  5. J

    ih baler

    I've got a IH 430 that would break the twine or miss the not like yours. We switched to 9000 plastic and now we get about 1 or 2 a day that don't tie right.
  6. J

    bailer twine (for square bailer)

    I use 9000 plastic as my International 430 will break anything else. But I get mine at fleet farm when I'm in Minneapolis. A bale of twine is about $27. The local ag stores here (Ashland, Wi)are around $35 a bale.
  7. J

    Round Bale Storage

    What are you feeding? If it's cows. The neighbor here swears by stacking one on the flat side and another upright on top. He used to stack them in a huge pile and tarp it, but that caused too much waste. He's been farming all his life and is 75.
  8. J

    Hay wagon

    If you want to lower it why not get some low profile 16" tires. Like something off a pontiac vibe (205/55/16 I've got some use ones here that I'm keeping for my mower conditioner). They have a hight of 25" They should hold that weight just fine as most are rated for 1300 lbs. So that's right at...
  9. J

    Massey Ferguson 65 diesel tach/hourmeter

    Agco offers the tach in the Heritage line pn 193969v91 but it's like $200. I also need this tach and am trying to locate one that isn't so expensive.
  10. J

    Round baler for Massey 65 diesel?

    Looking to get a round baler as I'm tired of throwing square bales. What would be a good one for my Massey 65 diesel?? It's a 50 hp tractor.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top