(800) 853-2651
SHOP NOW

Recent content by JWCarp

Yesterday's Tractor Forums
  1. J

    1256 brake problem

    Thank you all for the information. I will give you an update tomorrow.
  2. J

    1256 brake problem

    You are right I don't have to pump the brakes, but for what ever reason, that helps the left brake pick up pressure sooner. I have bled the brakes before. I suspected the adjusters and checked them, but I must have missed something something on the adjusters. I did have had the brake valve...
  3. J

    1256 brake problem

    Thanks for the information. I just went out and check the screw on the back of the brake booster rod and it was tight. The spring appears to be held down about the same as the other side and the upper part is tight. The oring on the piston also seems to be fine. Any other thoughts?
  4. J

    Farmall with 282d or ih 826

    If the condition of the tractors is the same, the 826 is more valuable and a 15 to 20 hp bigger. I like the 26 shifter better than the 06. Engine rebuild for either can be tricky and expensive. D282 rebuilt if not done right will not hold up. D358 rebuild is expensive. I have 2 706's. Now...
  5. J

    1256 brake problem

    I have been chasing this problem for a while. If I push on both brake pedals at the same time they go all the way down with virtually no braking at all. If I pump the brakes once and hold them down the pedals will eventually push back at me and I will have brakes again. If I let off the...
  6. J

    1256 TA Dump Valve and Brakes

    My 1256 loses the brakes each time I push in the clutch and the dump valve is pushed. Any idea what is going on? Any help would be appreciated.
  7. J

    ot lever guns

    If you want a pistol cartridge I would get a Marlin 1894 in 44 mag. Unless you reload, you don't want as 45 colt for hunting. It will work fine, but you can't get the same power of load due to 45 colts being loaded to lower pressures. If you reload, you can make the colt pretty hot. I would...
  8. J

    Headlight Bulb for UK Ford

    Thank you. I was hoping to find the original bulb. I would like to keep the old tractor as original as possible, but at least I know which light will fit it if I cannot find the right bulb.
  9. J

    Headlight Bulb for UK Ford

    I have a 6600 ford made in the UK. The front headlight bulbs are a different style (Stanley type I guess). It is a high low bean bulb. Do any of you guys know where I can get a bulb?
    • JWCarp
    • Thread
    • Replies: 4
    • Forum: Ford
  10. J

    IH 435 Knotter

    I have a 435 with the all twine knotter. I bought this baler just to have this newer knotter. The right side would give me problems once in a while, but the left side never missed a knot. Once I got the right side working the left started missing. It misses all the time. The twine knife...
  11. J

    Cultivator bracket

    I will check but I am sure that I have more than a few.
  12. J

    Round Bailer

    They are a good baler. We have had one since 94 and have had really zero issues with it.
  13. J

    Help Identify grinder

    David Where are you located? I might be interested.
  14. J

    Vermeer 605 Super G, starter flaps Springs

    This baler should either have 2 sets of springs on each side or it should have 1 set of springs and a hydraulic cylinder in the top middle of the baler. On my 1560, it has the cylinder. The cylinder has a pressure adjustment. You can crank the pressure up and make bales way too hard.
  15. J

    Rims for a D19

    I might be able to. Seems like when they are rusted in one spot, the rest if sometimes not far behind. Won't know for sure until the tires are off.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top