(800) 853-2651
SHOP NOW

Recent content by Kalamazoo

Yesterday's Tractor Forums
  1. K

    MF 2135 3pt in constant pump

    Is this a draft control installed wrong? Tractor was purchased this way.
  2. K

    2135 power steering ball joint

    Yes, the part book number doesn't fit.
  3. K

    2135 power steering ball joint

    How close were the 230 and 2135 power steering setups? I cant find a tie rod that fits a 2135, everything matching a 2135 has the wrong female thread and taper. The end for a 230 seems to have the correct thread 1/2-20...
  4. K

    Exhaust Manifold

    I'm buying a new exhaust manifold from this site, will the face of the manifold need machined before install? I was told they might.
  5. K

    Type A ATF substitute

    This is a MF200 loader. I have considered UTHF but read the multigrade is not generally recommended in dedicated hydraulic system.
  6. K

    Type A ATF substitute

    My loader call for type A ATF, 6 gallons. Is ISO 46 a acceptable substitute?
  7. K

    MF 200 loader

    Anyone have a MF200 loader? Just got one but its missing the dipstick. Could you measure your dipstick so I can determine the correct oil level?
  8. K

    Diagnosing knock

    It's not coming from the engine...
  9. K

    Diagnosing knock

    Update: Ran without knock, then knock appears... Knock disappears again after 2 minutes. Pushing in the clutch slowly brings knock back but everything seems ok above inspection plate. Now the tractor is not knocking at all?
  10. K

    Diagnosing knock

    Any tips to diagnose a MF 2135 knock? Its a continental 4 cyl. gas. Would pulling plugs and rolling it with the starter be enough to replicate?
  11. K

    MF135 Banjo fitting

    It's a brass block mounted to the steering column. My threads are stripped and it's the only thing keeping me from having working power steering. Iv'e looked everywhere without luck, any ideas? Part # 1031006m1
  12. K

    Lawn Mower Belt

    I took the drive belt off my riding mower and measured it last night, the width came out at 9/16". Assuming this is a 1/2" belt I went to order the new one but they are all listed as 5/8" belts. Do belts wear that much over 8 years?
  13. K

    groundhogs HELP

    Bait a live trap with chucks from a salt lick. I've gotten 2 in one trap before, works every single time.
  14. K

    MF135 charging system

    Alternator is a 508545M92, I believe original. Tractor has no lights.
  15. K

    MF135 charging system

    Sorry it's a 3 cylinder Perkins gas
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top