(800) 853-2651
SHOP NOW

Recent content by Keith Calhoun

Yesterday's Tractor Forums
  1. K

    Farmal B head

    Where are you located - I have a good head for CHEAP. Its off a 47 Farmall A, so it wouldn't be the correct date code, but should work fine for you... I'm in Lisbon Maryland.
  2. K

    1944 Farmall A work light

    Does anyone know what the correct work light for a 1944 Farmall A should be? Should it have the little red light on top, correct switch knob ect. I am trying to do as close to possible correct restoration as possible. Pictures would be great. Thanks, Keith
  3. K

    Ford 2000 steering boots

    I was wondering if anyone had a source or part number for the drag link boots used on a 1964 Ford 2000 tractor. I also need the ones that go on the power steering cylinders ends as well. Thanks, Keith
  4. K

    1958 MF35 Deluxe

    I just got this tractor, really like it and it seems to have been well cared for. It has the vertical exhaust right not, but we would like to put install a horizontal system if we could. It does have the Sauder loader, and Sauder snow plow, so we were wondering what horizontal system will fit...
  5. K

    paint color 1964 Ford 2000

    Was wondering if it is the same olive gray color like the 8Ns used. I have an unpainted original 2000 and the fenders look a little like the 8N gray. But I can't be certain. Anyone of have a color code for Tisco paint or other?
  6. K

    paint color 1964 Ford 2000

    What color gray is used on the front rims and rear wheel centers and fenders on a round sheet metal 4 cylinder 1964 Ford 2000? Thanks, Keith
  7. K

    pie weights

    Does anyone know where I can get, or the part number for the rubber keeper that is on the pie weight bolt on each weight for my 1964 Ford 2000? Thanks
  8. K

    brush mower

    I am new at running a brush hog type mower. My question is, the mower I bought only has a shear pin, I was thinking about adding a slip clutch to protect the mower and tractor if I hit something solid. If I add a slip clutch do I still need a ORC, or can the slip clutch also handle the ORC...
  9. K

    Farmall A steering seal

    Does anyone know a NAPA part number for the shaft seal in a Farmall A steering box. The seal that seals the shaft for the pitman arm. I'll also take the number for the seal that seals the steering wheel shaft if you have that handy too. I have the IH number, just trying to cross reference them...
  10. K

    Farmall A casting codes

    Does the transmission case on a Farmall straight A have a date code, or any other casting codes cast into it? If so where would they be located. I have a 1944 Farmall A, and I want to put a 1947 transmission into it, but I might swap the guts to keep the casting original to the tractor unless...
  11. K

    JD 420T Engine Timing

    My father is rebuilding the engine on his 420T 2 cylinder JD. He says he thinks he does not have the engine timing set correctly, something about timing the oil pump to the crank/cam, which will set the timing for the distributor since the distributor is driven off the oil pump. Can some one...
  12. K

    TO-20 questions

    I am thinking about buying a TO-20 local to me. I went and took a quick look but plan to go back soon and give it a test run. Problems, I noticed, the steering column/shaft would rise up when the wheel was turned. Is this just a bad bearing or?? Is everything available to overhaul this box... I...
  13. K

    Farmall A steering

    I am working on a steering box for a Farmall A - it is the later style keyed taped shaft with nut and cotter key. I am using a tie rod puller to pull it. I have heated it and quenched it while hot with penetrating oil but I can not get it to release. what is the trick? Thanks for the help. Keith
  14. K

    Woods L59 mower?

    Will the brackets for a Cub mount the L58 mower up to an A model Farmall since they are very similar? A guy has an L59 mower for sale with all the mounting brackets for a cub, will that match up to an A? Thanks for the help guys - Keith
  15. K

    Farmall A steering box

    Great info, thanks - this is exactly the info i needed. I guess the '47 box I am going to use the tapered shaft and arm out of must of had its steering rebuilt near the end of its life becasue from what you describe it sounds like it had the square shaft when new, but now has the tapered and...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top