-
Kkencombs replied to the thread Delco 10 SI question.I was just thinking about that, my first battery charger was an electric motor and alternator on some angle iron pieces. Also served...
-
Kkencombs replied to the thread Ingersoll Carburetor Troubles..Make sure the fuel lines are flexible and seal on the fittings well. Also, if that one has a pulse line it must be airtight also...
-
Kkencombs replied to the thread American made tools from the 50's & 60's..Best 1/2" ratchet I've ever owned was a Penncraft. Finally started slipping about 10 years ago, after over 50 years of use. And like...
-
Kkencombs replied to the thread Ingersoll Carburetor Troubles..Yes, if not, test as mentioned above. Sometimes I can't hear them, hearing issues, but place you finger on it and you can feel it...
-
Kkencombs replied to the thread Ingersoll Carburetor Troubles..Could be either. Easy to test, just rig a jumper wire direct from the battery to the solenoid connector. You should hear and feel it...
-
Kkencombs replied to the thread Ingersoll Carburetor Troubles..If the 'brass thing' had a wire connected that's probably the fuel solenoid. It plugs the main jet when not powered, retracted.
-
Kkencombs replied to the thread Ingersoll Carburetor Troubles..If your3014 is one of the later 2cyl briggs engined models, it probably has a fuel shut off solenoid on the carb. It must retract when...
-
Kkencombs replied to the thread Cub cadet 7305 wheel bolt pattern.Or, outside of one to inside of the other. No other math needed, and is pretty easy to do accurately with a digital caliper.
-
Kkencombs replied to the thread Vom recommendations.So true. I have a truly full auto meter, forgot the brand but, really good one. Anyway, it is limited in what it measures, but does...
-
Kkencombs replied to the thread Changing oil.I use two good floor jacks, located at the jack/lift points located close by the rear of the front wheels on most all unit bodies...
-
Kkencombs replied to the thread Vanguard 35hp no vacuum pulse from manifold.Replying to my own post. I've had some Vanguards but all 16/18hp. I think they had the pump attached to the valve cover/crankcase...
-
Kkencombs replied to the thread Chard Coffee grounds in concrete.It is likely due to the sugar in the Coke. A very small amount of sugar added will slow it down. A little too much and it'll never...
-
Kkencombs replied to the thread Vanguard 35hp no vacuum pulse from manifold.I don't understand how a pulse pump would ever work off the intake manifold? There is no pulse there, ever. At least no engine I've...
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy