(800) 853-2651
SHOP NOW

Recent content by kendal

Yesterday's Tractor Forums
  1. K

    elwood front end

    has anyone found the plans or patent dimensions for the drop chain box off of the belt pulley housing. i was currius how difficult it would be to manufacture my own. id like to put a front wheel assist under an m and a 450. the front axle appears to be a spicer front end but i could be wrong...
  2. K

    elwood front end

    has anyone found the plans or patent dimensions for the drop chain box off of the belt pulley housing. i was currius how difficult it would be to manufacture my own. id like to put a front wheel assist under an m and a 450. the front axle appears to be a spicer front end but i could be wrong...
  3. K

    elwood front end

    im looking for the front drop box off of where the belt pulley mounts for an m farmall. looking for any information that i can and any pictures or parts would help.
  4. K

    carb?

    i have a carb and was wondering if anyone can help identify it to get a rebuild kit. it came off of a farmall 300 that was farm fuel. the part # is 363741R91. the carb looks identical to the gas carb on my dads 300 farmall. havnt compared part# yet. thanks.
  5. K

    carb?

    i have a carb and was wondering if anyone can help identify it to get a rebuild kit. it came off of a farmall 300 that was farm fuel. the part # is 363741R91. the carb looks identical to the gas carb on my dads 300 farmall. havnt compared part# yet. thanks.
  6. K

    allis sleeve

    what is the thickness of a stock d17 sleeve in the oring groove and at the thickest point on the sleeve.
  7. K

    allis sleeve

    what is the height and outside dimension of a d17 sleeve. on a sleeve with the 4 1/8 bore how thick is the sleeve from the ID to the OD?
  8. K

    pressed steel rims

    i am planning on running a 13.6 by 38 tire. so i believe a 14 inch rim is what im looking for.
  9. K

    pressed steel rims

    looking for a set of 9 bolt pressed steel on a 38 inch rim
  10. K

    2 point?

    im not going to be using the 2 point on this tractor and am wondering what the going rate for a complete 2 point with a draft control is?
  11. K

    2 point?

    i bought a 300 international with a 2 point on the back of it. iv seen 2 points before but this tractor has another hydraulic cylinder on the drawbar that is belly mounted on the right side. it looks like an early form of a draft control. im currius what is the purpose of this. and what is the 2...
  12. K

    14.9 38 tires

    im looking for a set of 14.9 38 tractor tires in the nebraska area.
  13. K

    350 diesel hydraulic pump

    im looking for a rebuild kit for hydraulic pump for a 350 farmall tractor with a continental engine. it is a pesco pump, and the IH part number is #352438R94. any help would be great apreciated.
  14. K

    engine sleeve

    i was just currius. iv heard of a person that welded a hydraulic cylinder into a john deere block to get as large of a bore as he could. and i just didnt know if anyone else has tried this?
  15. K

    engine sleeve

    i was currius if there was anything special about the steel that sleeves are made of. i wondered if by taking a heavy walled pipe and lathing down the OD dimensions to fit my aplication while keeping the counter bore ridge. then hone the ID diameter to match my piston bore. is this possible or...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top