(800) 853-2651
SHOP NOW

Recent content by Kendall

Yesterday's Tractor Forums
  1. K

    Coleman Generators

    try here Powermate manuals
  2. K

    rebuilding DeWalt cordless drill batteries

    these guys can rebuild them with higher capacity cells. voltman battery rebuilding service
  3. K

    paint color

    right here at ytmag paint codes
  4. K

    chain saw

    Give up. V8 chain saw
  5. K

    Farmall Model A

    You"d be happier with a Super A. Just make sure its got all the cultivator stuff to go with it.
  6. K

    weed killer Roundup???

    Anything with MSMA in it will kill a lot of weeds but not kill bermuda grass. I dont know what kind of grass you have, maybe worth a try.
  7. K

    Cooke County Antique Tractor Farm Show PICS

    Thanks for the pictures. I usually get to that show every year but had too many irons in the fire over Labor Day weekend to make it. Looking forward to next year's show.
  8. K

    Farmall won't start #2

    I'm betting my money on a gummed up carburetor. After setting a year, it has dried out and clogged the jets. Been there, seen it, done it. Take it apart, clean it out, run a tiny wire through the jets to clean them. If you want to verify its the carburetor, shoot a bit of starter fluid into it...
  9. K

    Super A

    That rang a bell in my head so i looked back through the archives and see you've been searching for an answer since Dec of 1999... http://www.ytmag.com/cgi-bin/viewit.cgi?bd=farmall&th=51536 and again in Dec of 2005... http://www.ytmag.com/cgi-bin/viewit.cgi?bd=farmall&th=527558 i think i've...
  10. K

    Super A right brake pedal

    My email would be great. Thanks.
  11. K

    Super A right brake pedal

    Yes, I'd sure like to see those pictures. My left side needs seals and a brake band. My right side works great. thanks
  12. K

    Super A right brake pedal

    Yes, both pedals are butting up agaist the stop at the floor pan. Its just that 58 years of mashing mostly on the right pedal, i guess, has bent it down about 3/4 inch. I just didn't want to torch on it and then discover it's cast iron and cant be torched and bent. I understand about adjusting...
  13. K

    Super A right brake pedal

    I had the wollowed out shaft fiexed up real nice with a brass bushing and grease fitting. I guess years of mashing on the brake has slowly bent the bar down a little. I understand about adjusting both brakes to grab at the same time. I just need to get them aligned to start with. Thanks everybody.
  14. K

    Super A right brake pedal

    The right brake pedal on my Super A doesn't line up with the left pedal. Is this something I can heat up with my torch and bend back until it aligns with the left one? It only needs to go back about 3/4 inch to allow me to lock the pedals together.
  15. K

    dual compressors to increase cfm

    Tandem implies one compressor feeding another which would be the Department of Redundancy Department for compressing air. However, logically thinking, 2 compressors in parallel whould acomplish what youre talking about. If you do so, you probably want to increase the size of the pipe coming out...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top