(800) 853-2651
SHOP NOW

Recent content by keysem

Yesterday's Tractor Forums
  1. K

    Z129 anyone have a rebuilt head?

    I have a block that the webs were welded on. I have replaced the head gasket twice now. The last time I had the head off I inspected the block and the head very closely but didn"t find any evidence of a crack from the outside surfaces. However, I had some engine timing issues that led to the...
  2. K

    TO20 Three point lift problem

    Check out the comments at the following link for this issue. http://www.fergusonenthusiasts.com/restoration%20helps/tech/Lift%20Arms%20Stuck%20in%20Up%20Position.pdf
  3. K

    Lift cylinder leaking.. what's my next step?

    I have a TO30 with a 2.5" hydraulic cyl bore. I replaced my piston / rings with one from a NAA ford Jubilee this past weekend. I got the idea from a hydraulic repair video I bought from this site. This conversion is basically universal to all of the fords and fergusons that share the 2.5"...
  4. K

    Ford NAA Hydraulic Piston Swap onto a TO30

    I finished the conversion this weekend. Everything works great. The Hydraulics hold pressure without the PTO on and they run strong and smooth. I'm very happy with the results!
  5. K

    Ferguson Manure loader

    I removed this same loader attachment from my TO30 and would be willing to part with it for parts if you find you need them.
  6. K

    Ford NAA Hydraulic Piston Swap onto a TO30

    The reason for the swap was mentioned in the video as the hydraulics will not bleed down when the PTO is not egaged while the 3pt system is under load. I have been dealing with this issue on my TO30 as long as I have owned it, and I was happy to find a possible solution. I know the bore of the...
  7. K

    Ford NAA Hydraulic Piston Swap onto a TO30

    Guys, I purchased the hydraulic system repair video that is available through the yesterday"s tractors video collection. In that video they focus on the ford 2N, 8N, 9N, and mention the ferguson TO20 & 30 tractors as being similar. When making the replacement of the hydraulic cylinder piston...
  8. K

    TO30 front end loader

    I decided against the loader. Thanks for all your input.
  9. K

    TO30 front end loader

    I'm considering putting a front end loader on my TO30. Can I run the hydraulics off the hydraulic ports under the seat or do I have to use a PTO pump/reservoir. If I have to use the additional pump / reservoir can I mount it to the crank in the front of the tractor? If so, is there a...
  10. K

    TO30 3pt hitch hydraulics

    I thought my system was a bit excessive. With an implement on the 3pt hitch it would leak down in about 1 min without the PTO on.
  11. K

    TO30 3pt hitch hydraulics

    Last winter I decided to "rebuild" the hydraulic chamber while replacing the broken PTO shaft. I decided to mess around with the hydraulics because I was experiencing a slow leak in the hydraulics when the PTO/hydraulics weren"t engaged, but the 3pt hitch was raised. After reassembling the...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top