(800) 853-2651
SHOP NOW

Recent content by kgreg

Yesterday's Tractor Forums
  1. K

    Searching for Super C Shafts

    My super c has the jamb nut style. Not sure where you are located. I'd probably more than likely sell the whole lever assembly versus taking it apart. 763-898-9477
  2. K

    Searching for Super C Shafts

    I've got a super c I'm parting out. Located central mn. I'd have to look at what style it has.
  3. K

    Farmall m value

    Might be interested in it depending what you come up with on price. Located in Central mn
  4. K

    Minneapolis Moline hwy dept. Tractor

    Yes that would be an rti, I have a 1954 rti with the lull loader, and as you describe that's how this one is. You interested in buying one?
  5. K

    Farmall C, 9 bolt hubs????

    MM r hubs are nine bolt. I believe the axle is the same size I would have to measure to make sure. The key way on th mm hub is 3/4 and the ih c is 1/2? You would need a machine shop to make a step key for you. I'm in central mn and would have a set of mm r hubs.
  6. K

    Rear rims

    I've got a set of 30 inch, 16.9x30 tires and rims off a farmall w6 for sale. Located in Central Minnesota.
  7. K

    Farmall H with 9 speed

    I'm looking at a farmall h with a 9 speed transmission. The tractor runs and drives good, smokes a little bit. Has new 11.2x38 firestones on the rear and new tires on the front. Tractor also has fenders with a faded paint job from sitting outside. Normally around Central Minnesota thats about a...
  8. K

    2021.06.17 Rust Pic

    That looks to be an IH w6 or more than likely an I6 the industrial version.
  9. K

    M parts on a BN?

    I have a farmall b for parts. There is a gas tank and a hood. Located in central Minnesota if that helps you.
  10. K

    Wheel weights

    Hi not normally on the john deere page, but have a question. I bought a set of weights at an auction a while back. They have JD 25B on them. They are pretty thick guessing 4 to 5 inches thick. Wondering if they are in fact John deere and what model they would have possibly been for? Thanks for...
  11. K

    IH Super C...

    I've got an artsway belly mower off a farmall b. You would need different brackets for your c. I'm located in central Minnesota.
  12. K

    need 32 rims for a red face U

    I had time to get a measurement and yes it is 12 inches wide. Has some rust but might work for you.
  13. K

    need 32 rims for a red face U

    I've got one 32 inch rim from a red nose uts I parted out. It has been cut and widened. I'm located in central mn.
  14. K

    Farmall super h update

    That was kinda my thoughts. Other than the choke coming out on the other side of the carb is there any other difference between a super h and a m bottom part of a carb?
  15. K

    Farmall super h update

    I had a extra farmall m carb in my parts so I decided to try some stuff. When I took the m carb apart I noticed theres a little part of the jet that sticks up into the upper half of the carb. Took my h carb apart and here to find out it's been twisted off below the face of the lower half of the...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top