(800) 853-2651
SHOP NOW

Recent content by Kimbob54

Yesterday's Tractor Forums
  1. K

    54 To 30

    I haul fire wood, dirt, tools etc. The tractor in the background is a 1959 Cub Lo-Boy.
  2. K

    54 To 30

    The carry all frame was purchased at Rural King Ag store. I saw a post online with pictures and I kind of copied the design. There is an end gate that can be pulled out and slid in to make a seat. I used mainly 5/4 treated decking except in a few areas.
  3. K

    Cub Hydraulic Problem

    I rebuilt mine about 15 years ago. I just did not want to Tear it down if it could be the pump?
  4. K

    54 To 30

    I haven't been on here for a while but visit everyday. I wanted to send a picture of my To30 with a carryall I made. I repainted the tractor and made many repairs To get it in good shape. My Wife called it the money pit Until I got it back together.
  5. K

    Cub Hydraulic Problem

    I have a 59 Cub Lo-Boy with the hydraulic unit to lift a one point hitch. The position lever got stuck and and I freed it. Now the unit will move up and down but without any Weight. Put weight on it and it can't lift. I have checked the fluid level and it is good. Any ideas on where to look...
  6. K

    To 30 3 point question

    Remember you have no down pressure. My blade rides Up sometimes when I push my burn pile.
  7. K

    Distributor cam bushing

    I had the same thought and put a small amount of dielectric grease on the cam frequently. No movement in the shaft either. Might pull the shaft out and build up the worn area or just buy a new shaft. I wonder how much clearance there should be between the shaft and cam hole? .010?
  8. K

    Distributor cam bushing

    I suspect the old worn out advance wore the shaft. I could mic it and suspect it should be the same diameter as the top?
  9. K

    Distributor cam bushing

    I had to replace the centrifugal advance on my 52 8N (side distributor). The old one was falling apart. I bought the new one from this site. There is no brass bushing in my new advance and there is slop and the cam will move about 1/8 of an inch. I can set the points and it runs well but it...
  10. K

    engine oil

    I use 10w30 in my 54 TO30 and have great oil pressure (35). I just buy a good brand. Engine was rebuilt in 1994. Has about 600 hrs on the rebuild. Doesn't use any oil either.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top