(800) 853-2651
SHOP NOW

Recent content by kip1456

Yesterday's Tractor Forums
  1. K

    Design Suggestions on Building Dead Weight Sled

    Looking to build two sleds for dead weight pulling, one for on dirt and one for on cement. I have a supply of 1/4" steel plate to work with in sheets 46 inches wide by 20 foot long. The one for cement thinking of putting wood on bottom of plate. How big? How long? How long of chain? Maybe run...
  2. K

    Ambac on 220

    What all would I have to change to mount an ambac injection pump and lines off of a L3 gleaner combine with the 670T motor on to my AC 210 or 220 tractor with the 426 motor. Is it a bolt up or are things different in the front cover and idler gear?
  3. K

    Help, JD 4010 stuck in gear!

    Had a 5020 that done same thing stuck in forward gear. What caused it was dirt had built up under the shifter rod clevis and arm on top of the trans housing and wouldn't let the arm go back down to get into neutral. I had to dig the dirt out from the right side cowling bottom where it meets the...
  4. K

    MF1085 injector pump

    Make sure that you are not off one revolution on the crank. Make sure both valves are closed on #1 cyl with the pump and timing marks aligned. Some engines will run 1 off, some won't.
  5. K

    5020 cab removal

    I already have a 5020 w/o cab and the batteries are under the platform on the left side. the small panel behind the clutch lifts out then does the left floor panel over the batteries. The cab tractor has the batteries in a box on outside of left engine side rail by the starter. There is a floor...
  6. K

    5020 cab removal

    Looking at a 5020 with a crenlo cab and would like to remove the cab. I can get fenders and mounts but what else would I need. Would I need floorboards from an open station or are they already there under the cab floor? Anyone else already has done this that can give me a heads up.
  7. K

    MF Salvage Yards

    http://worldwidetractorparts.ohag4u.com Used to be a massey dealer.
  8. K

    Tractor Pull at Paulding, Ohio

    Tractor Pull at Paulding, Ohio Fairgrounds on Saturday June 6, 2015. Weigh in starting at 8 am and first hook at 10 am. Antique Div 1, 2, Shootout classes 2500 to 10500, and field stock classes 6500 to 15500, hot farm 8700 and 9500. Full info at our Facebook page Black Swamp and Maumee Gas...
  9. K

    180 pto grinds when engaging

    This has been awhile but if I remember correctly my 180 had a lever on left side of seat with 3 positions, ground, neutral, and engine. Then you have a two stage clutch pedal. Push it part way down ground travel stops, rest of way down PTO stops. A little trick I remember was to engage engine...
  10. K

    Calling rrlund

    Thanks. Already sold!
  11. K

    Calling rrlund

    I might be interested in that White 2-180 you posted in the other thread. Would like to know contact info if still available for price you quoted and location. Can email me at [email protected] Thanks.
  12. K

    Major Muscle On CL!!

    Tell me about the one for $8000, I might be interested. Location? Still available? Contact info?
  13. K

    Shipping How-to?

    Go to your local Fastenal Store. They do store to store very reasonable.
  14. K

    Aultman Taylor Matchless Cloverhuller Size 4

    Anyone have any interest in this? Our county Historical Society is over full and is getting rid of some stuff. If someone would be interested in keeping or restoring it and not scrapping it out let me know. Located in NW Ohio.
  15. K

    MF 1155.....question for dieseltech

    If memory serves me correct, a fellow I know that pulls a massey v8 told me that columbus diesel told him that not to interchange injector tip between 510-540 and the 640 because of different spray patterns for the heads are different.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top