(800) 853-2651
SHOP NOW

Recent content by KNJL

Yesterday's Tractor Forums
  1. K

    47 g for pulling

    Thanks I think I will go that way
  2. K

    47 g for pulling

    Ok maybe lengthening my rods would be a better option . Who did you have do the rods ? About how much does it cost ?
  3. K

    47 g for pulling

    I am thinking about doing some modifications to my 47 g ( yes g not gm ) for pulling . If I put the unstyled head on should I use an m&w type aluminum piston or a jd gas piston ? Any advice on best compression ratio to aim for ?
  4. K

    820 2 cylinder front wheel weights

    The weights that mount inside , are they just or after market ?
  5. K

    B2016r weights

    Are after market b2016r weights available ? If so anyone know a place I can get them ?
  6. K

    820 2 cylinder front wheel weights

    It looks like the weights in the picture bolt on with 3 bolts at the hub. The jd1276r front rims have 4 bolt holes in them , are the 4 bolt holes in the rim for an after market weit like f&h ?
  7. K

    820 2 cylinder front wheel weights

    Anyone have a picture or part number for original John Deere front wheel weights for 820 ? Front rims have bolt holes for weights so I assume weights where available for them . Anyone know about them ?
  8. K

    engine timing with high compression

    thanks guys for all the info
  9. K

    engine timing with high compression

    anyone have a suggestion on what to do with timing settings when increasing the compression. lets say you change an all fuel tractors compression from the original 3.75 to 1 up to a 9.47 to one. would you back off the timing from the factory setting due to the higher compression to prevent...
  10. K

    g or gas 70 valve spring coil bind

    anyone know what the coil bind measurment is for a g/70 gas valve spring ?
  11. K

    unstyled a heisler valve springs

    anyone have installed valve spring height for unstyled a heisler head valve springs. i am cutting of 70 gas valves and then cutting new lock grove.do not have any original valves or springs i am trying to make the 70 gas valves work and that looks like no problem. just having trouble with spring...
  12. K

    JD CLUTCH

    hack up? if the gears fit on my trans shaft wich thay do - had them in my hand about 8 hrs ago and take a look at some info the late a and the 60 both have the same number of teeth wich both have a lower gear reduction than a unstyled a. i was just hopeing to get a awnser from someone that has...
  13. K

    JD CLUTCH

    thanks for the info i will look for a late a setup. would i be able to use just the 2 reduction gears and just use my existing clutch pully?
  14. K

    JD CLUTCH

    ha ha about the yelling sorry i am not a computer geek. i do not want to know about an interchange i want to "mod" it to the new type of clutch and slow down trans input speed by switching to the different reduction gears so i can use 2nd gear.
  15. K

    JD CLUTCH

    ANYONE KNOW IF A JD 60 CLUTCH SETUP AND FIRST REDUCTION GEAR WILL FIT INTO AN UNSTYLED JD A. I AM USEING A 40 A CRANK AND CLUTCH DRIVER RIGHT NOW. I WOULD LIKE TO INCREASE THE NUMBER OF CLUTCH DISKS AND ALSO SLOW THE SPEED DOWN SO I CAN POSABLY USE 2ND INSTEAD OF FIRST. FIRST THE TRACTOR HAS...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top