(800) 853-2651
SHOP NOW

Recent content by KS 640

Yesterday's Tractor Forums
  1. K

    WD 45 pto housing question

    Several years ago had to replace a bearing and reline the brakes and its now leaking oil around the pto assembly. Noticed one of the bolts is stripped and needs replaced.
  2. K

    WD 45 pto housing question

    What is the size of the stud bolts used to attach the housing to the power tube, and the size of nut used for a WD 45?
  3. K

    WD45 Sediment Bowl

    Same thing happened to mine several years ago, unscrew the cap and valve and replace the o-rings or gasket fitting inside. When I replaced mine, I used the same diameter, but a thicker o-ring.
  4. K

    '50 8N

    If you have good compression, then look at the spark side, could be an issue with rotor, cap, or plug wires.
  5. K

    First timer here looking for help.

    Had a tractor that would only run 15 to 20 minutes (not a Massey),and we had to replace the intake manifold gasket. Seems it would get hot and not seal properly and a leak between the manifold and block would occur. Have to wait a while before it would run again. Might try choking before it...
  6. K

    Manifold sealant question

    I am getting ready to put new metal ring intake and exhaust manifold gaskets on an Oliver 1855 gasoline 310 waukesha engine. What is the best sealant for this type of manifold gasket arrangement?
  7. K

    1855 gas engine manifold question

    I am replacing the intake manifold gaskets on an Oliver 1855 with 310 gasoline waukasha engine. What is the proper amount or torque for tightening the manifold stud bolts?
  8. K

    WD 45 Ignition/wiring issue

    Finally found the problem, it was a broken wire. Found it by testing the wires. Tractor now starts and runs again. Thanks!
  9. K

    WD 45 Ignition/wiring issue

    The solenoid has two smaller posts one is marked with an S this wire goes to the ignition switch, to a post marked SOL. The other small post marked with an I has no wire on it. The coil is 12 volt and was replaced about three years ago. The wire coming from the ignition switch marked IGN, goes...
  10. K

    WD 45 Ignition/wiring issue

    Recently had to clean out the gas tank on a wd 45. When placing the tank back on, I moved some of the wires around the solenoid. The tractor has been converted to 12 volts and has an alternator, and a keyed ignition switch. Noticed one wire came out of a wire fitting attached to the back main...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top