-
M
Does my 850 have a live PTO?
And yet, tractor data list 850s as have a 2-stage clutch live PTO https://www.tractordata.com/farm-tractors/000/0/9/99-john-deere-850.html -
M
Just bought a Pasquali tractor, what I found in cooling syst
Right. First I am checking and adjusting, greasing and oiling everything I can figure out. The park brake was frozen, got that fixed. Have to mount an alternator in the next couple weeks. It came with a logging winch, I will have to try that out. It is strange as it bolt right to the back...- M5040
- Post #1
- Forum: Lesser Known Manufacturers
-
M
Just bought a Pasquali tractor, what I found in cooling syst
I just bought a Pasquali tractor. I think it is a 993, but not sure. It has been sitting quite a while. I have been checking it over. One thing I found that is extremely important, and could happen over only a few days, is that the engine shrouding was packed full with a mouse nest. The...- M5040
- Thread
- Replies: 2
- Forum: Lesser Known Manufacturers
-
M
Pasquali Front Loader
How much for the blade and where are you? Can you send pictures to my email jam0000@yahoo(dot)com?- M5040
- Post #1
- Forum: Tractor & Farm Talk
-
M
mike pasquali tractor
I know this is an old post, but did you ever think of making the oil filter adapters to sell? I would like to buy one.- M5040
- Post #1
- Forum: Buyer/Seller Feedback
-
M
Old small 4wd articulate tractor - Trap Master
Took it out for quick run in snow- M5040
- Post #1
- Forum: Tractor & Farm Talk
-
M
Old small 4wd articulate tractor - Trap Master
That is the one! Now does anybody else have one?- M5040
- Post #1
- Forum: Tractor & Farm Talk
-
M
Old small 4wd articulate tractor - Trap Master
I have a Trap Master made by Stanley Clarke in the 1970s. If anyone has pictures, I want to finish a restoration on mine and need info on the correct emblems or stickers etc. Also the front or rear blades.- M5040
- Thread
- Replies: 9
- Forum: Tractor & Farm Talk
-
M
OIL BATH FILTER
No, just make sure it evaporates before you try and start the engine, so it doesn't run away. And oil the mesh with new oil. -
M
mud/sludge @ bottom of hyd on 841, best way to clean
I took the lift arm cover off my 841 and as expected, there is mud type sludge at the bottom. Has anybody had any problems with washing the bottom of the case out with diesel fuel? I am a little concerned about loosening something up and causing damage to hyd pump. I was going to just put the... -
M
pto control after sos to 4sp conversion
Thanks, The SOS control was drilled and installed as per the elenco instructions specificly for the driveline disconnect and it is just in front of the T-case (but it is a different position then a gear drive tractor would be). However now it doesn't move more then a slight fraction of an inch... -
M
pto control after sos to 4sp conversion
This was done years ago by someone else, I haven't found a doner tractor yet. What is the best way to work on this, 1 split the tractor or 2 take off the hyd lift topcover? Any negitives to spliting the tractor? It looks realy simple and easier then the hyd lift cover. I can't imagine how... -
M
pto control after sos to 4sp conversion
I have an elenco equiped 801 tractor with a 4sp converted from SOS. The PTO is engauged constantly with no ability to shut off. Does anyone have experience in correcting this? Looking through the fill port, I can see the control linkage goes to the upper shafts (which I think was the SOS... -
M
Sherman trans data plate on 841, location ?
Yea, mine is a 1961, I was hopeing for the steering wheel version as it seems easier to read. -
M
Sherman trans data plate on 841, location ?
Concerning the sherman 3 speed trans mated to the 4 speed in the Power Master 841 tractors, I see ads for a round data plate that goes under the "steering wheel nut" and/or a rectangular dataplate that mounts on the cowl under the steering wheel facing the driver. [The dataplate list the gear...
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy