Recent content by manni52

  1. M

    Counterweight for my 8N Dearborn

    Thank you all for all of the information, I have much to consider from stem to stern. I am hoping to get 'er in the "car hold" this winter to work on the hydraulics and the draft. Steer bushings and spindle bearings also need attention so all this before any ballast fab. Thanks again!
  2. M

    Counterweight for my 8N Dearborn

    Hello, folks! I have a question regarding the counterweight required for the Dearborn 19-22 mounted on my 8N. Currently the rear tires are filled with liquid for this purpose, but the liquid is leaking out of the valve stem holes causing them to rust badly requiring at least one of the rims to...
  3. M

    flooding carb

    [b:b2927b000d]Den N Ms[/b:b2927b000d]: sorry did not answer your ? No was not blowing black smoke, another good point. Did not look or smell like it was running rich. Tx!-J
  4. M

    flooding carb

    Hey folks, thanks for all of the replies! I have not completely got the hang of this forum communication so I hope all who desire a reply will see this. When I said the float level was perhaps set on the low side I meant that the needle and seat would seal early maintaining a lower level of fuel...
  5. M

    flooding carb

    Now that is something I had not thought of, thanks!
  6. M

    flooding carb

    Hello, all- I have an early Ford 8N with a Marvel Schebler carb TSX241C. I had recently put new parts in from a kit. The tractor runs ok for a while then just stops and will not start. I discovered liquid fuel running out of the choke housing, lots of it. The first thing I checked is the...
  7. M

    Bendix starter drives

    Hey everybody, Happy Fourth! Just thought I would get back those who assisted me with my Bendix drive. I came up with my own solution after some amount of dinking around which may be helpful to others. I realized that the large retaining washer that was giving me a hard time at the back of the...
  8. M

    8n lost it's spark

    Bruce, Thanks for all of the info! I double checked all 10 points and all seem to be ok. The resistance btw the post and the didst. cap tab is @ about 7k ohms not at 6k as you recommended. I still do not believe I have two bad coils. I am going to do some wiring repair, chuck the after market...
  9. M

    8n lost it's spark

    Hello, all, and a happy Fourth! Today after installing my new starter drive, got her started, and ran with a intermittent sput-sput. As I was getting ready to adjust the rebuilt carb I had put on before the drive failed, the tractor sputtered rapidly, died and would not start again. Gave the...
  10. M

    Bendix starter drives

    I will try the pipe jig and perhaps a bit of pin filing for good measure, thanks folks!
  11. M

    dearborn n series loader

    Looks like a new control valve is the way to go, save me the trouble, thanks Howdy!
  12. M

    Bendix starter drives

    Hey, everybody: Since I am new to the forum, and my 8n, I will have many questions that I sure could use help with. The next is with regards to the starter. The old drive crapped out and I have a new replacement that is different but I am convinced it will work onna counna many vendors are...
  13. M

    dearborn n series loader

    Thanks for the info. I have the numbers, I will look into Baum Hydraulics! -John
  14. M

    dearborn n series loader

    Thanks for the info. I have the numbers, I will look into Baum Hydraulics! -John
  15. M

    dearborn n series loader

    Hello all, new to the forum: Recently acquired a Ford 8n with a Dearborn loader attached. The control valve is leaking pretty bad and am having a hard time locating a repair kit to replace the seals etc.. The valve appears to be made by Parker. Does anyone here know of a place where I can...
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top