(800) 853-2651
SHOP NOW

Recent content by Mark-Ia

Yesterday's Tractor Forums
  1. M

    Fuel Tank Rust Removal

    Don't use a vacuum , the motor will ignite the fumes
  2. M

    John deere corn planter model 7000

    Should be able to do that. Start in the middle with a tape measure and marker pen. 1st row would be 15" from center, then 30" after that.
  3. M

    Passed again

    A friend of mine had a Dodge 3/4 ton with the V10. He would start it when cold to let the engine warm up, seems the oil pump would starve the rear main when cold. After the 2nd engine he traded it.
  4. M

    Passed again

    Seen $3.48 in Waterloo Iowa Saturday.
  5. M

    NEW HOOD FOR 455 MOWER

    You might be able to decals from Hapco.
  6. M

    Brakes on '50 AR?

    The 49 only have a service brake. If you wanted brakes on both wheels you'd need to order a Orchard package as they had turning brakes like the later one.
  7. M

    1940 John Deere Model A front wheels wobble.

    Try adjusting the sector gear 1st before replacing it. There are youtube videos showing how to do that. Very easy.
  8. M

    Shop lighting

    Amazon has High Bay Led shop lights. They are round and plug in a normal outlet. My brother put 4 in a 32x40 shop and has plenty of light.
  9. M

    Aftermarket Water Pump Rebuild?

    Looks like a Johnson aftermarket water pump. I wouldn't mess with it. Perhaps advertise it for someone to hang on their wall.
  10. M

    999 2 row planter

    Not sure on the time frame, but you could buy an adapter to make it a 3-point hitch from Tractor Supply in the late 50's.
  11. M

    Tecumseh HH60 Ignition Cam misalignment

    A screwdriver and short the spark plug and it will die.
  12. M

    New to group

    There are 3 carriage bolts that hold the spindle assy. to the deck. You may need to cut or torch them off to get the spindle assy loose. After you get the bearing assy. from the deck, Put the top nut in a vice and screw the bottom off the spindle. Tap the spindle out of the housing. There is a...
  13. M

    New to group

    Deck bearings are all the same on those decks. JD9296 for your bearings.
  14. M

    Deere Seal Needing Replacing, Couple Questions

    I think I would leave the bearing alone as it runs with oil.
  15. M

    John Deere 80 Injectors

    Garry rebuilds 2-cylinder injectors and pumps.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top