(800) 853-2651
SHOP NOW

Recent content by Massey3518

Yesterday's Tractor Forums
  1. M

    Massey ferguson 35 draft control assembly

    Yea I just went ahead with the Draft level on the dot position >o< on the quadrant and left the draft control assembly with no end play. Seems to be working ok. Very little information anywhere about the draft control settings. It's just fine tuning it yourself I think
  2. M

    Massey ferguson 35 draft control assembly

    Does anyone know where the position and draft control levers should be on the quadrant on reassembly of the draft control assembly?? I know you have to find the happy medium of no end float but that can vary on lever positions
  3. M

    Massey ferguson 35 draft control assembly

    Hi guys. I want to replace the draft control assembly on my MF35 as its all worn at the holes around the yoke and clevis to an oval shape. There's a slap in it up and down and in and out. I've had the assembly out a few years back when I had the lift heard off so there's no problem...
  4. M

    Blue smoke, worn guides?

    Blue smoke usually a fuel issue. Have you had the injectors and CAV fuel pump reconditioned
  5. M

    MF 35 Air Filter

    I understand you. Yes you can but the bottom oil baths separately.
  6. M

    Hydraulic working properly?

    It's an unusual looking diverter valve but still should work. The hydraulics on your tractor sounds to be OK. There's 2 ports on that diverter valve with only one in use and you mover the diverter lever to which ever port you need. Im assuming you've done that? When you divert you then...
  7. M

    AD3.152 rear main (rope seal) improvement

    Yes I've bought and installed one of these modified rope seals at Christmas last and so far thankfully there has been no leaking of engine oil. I've clocked many hours on the tractor over theast few months as it works on the farm. I posted about it here at Xmas. I had fitted a new clutch after...
  8. M

    MF 35 Air Filter

    There is an oil bath resivour in the bottom of the air breather of a MF 35. Them some steel mesh to filter out any particles that doesn't stick to the oil. I suggest keeping it this way and using some steel kitchen scours like this to replace the mesh.
  9. M

    Fordson Super Major

    Good point there thanks
  10. M

    Fordson Super Major

    Thank you I understand your points. I'll do that
  11. M

    Fordson Super Major

    OK thanks. In general do you find they hold back the oil? If for long at all after being replaced
  12. M

    Fordson Super Major

    Thanks for the info I will check those. Does the sump gasket cover go inbetween where the rope seals meet? Been looking at the gasket and it looks like it does?
  13. M

    Fordson Super Major

    Hi going to change the rear crankshaft rope seal on a fordson major that's been leaking since I bought it. Probably has never been changed since new so in reality will it be possible to get it stopped with a new seal and what's the best way about doing it. Thanks.
  14. M

    Ferguson 2 furrow plough

  15. M

    Ferguson 2 furrow plough

    Hi I've a ferguson plough I'm starting to restore. A few bits missing unfortunately. On the furrow wheel can anyone show me where the spring goes? It's missing on this one and the exploded diagram I have is not the best Any other information appreciated Regards
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top