(800) 853-2651
SHOP NOW

Recent content by matt bock

Yesterday's Tractor Forums
  1. M

    2470 rearend levels

    hello I just bought a 2470 tractor and cant find how to check oil levels in the front and rear pumpkins, all I can find is the vent on the top don't see a fill level plug thanks
  2. M

    190xt hi-lo

    dads got an early 200 with the up down shifter so id say the 190 has been modified
  3. M

    9600

    im looking at a 9600 the dual power slips in low how expensive are they to rebuild? Also steering box has a lot of slop what usually happens there? its cheap SO I don't mind doing some work to it. thanks
  4. M

    OT But Still Ford

    i had one do that and it was the anti theft key try a different key if you have one.
  5. M

    HELP !! 9400 combine just quit

    make sure your switch to swing the unload auger is in off position that will keep them from starting too
  6. M

    trenton il pull

    Anybody know where the pull is in Trenton Friday night? And I need cale mahnkes number I lost it thanks.
  7. M

    9600 ford

    I looked at a 9600 yesterday run good under load but has a miss at idle that comes and goes has sims inj pump no blowby do these have much injector problems or is this in the pump? Also shifter is a little sloppy how hard is that to fix? thanks
  8. M

    450 pop in exhaust

    id spray carb cleaner around the intake gaskets and carb to see if u have a vacuum leak that will make them pop at idle
  9. M

    waiting in line at the scale

    it was a long line to wait if the tractors that weren"t gonna pull for 3 hours would just wait till light classes are done would speed things up alot
  10. M

    9600 ford

    Also I was told this is a sleeveless motor is that correct?
  11. M

    Wd won't shift without grinding

    make sure a pin didn't fall out of one of the release levers on the pressure plate
  12. M

    Early AC 7000 PTO clutch pack

    I had the pto clutch out of one last spring pull the motor and u can get to it without taking torque tube off
  13. M

    D 17 pushrods

    u need to change the rocker arm mounts that's where the difference is pushrods all the same length from wc to d17
  14. M

    It's that time again

    I like how u put ur thumb in the way so u cant tell where the end of the tape is.
  15. M

    It's that time again

    nice of u to put ur thumb in the way so u cant tell where the end of the tape is nice trick photography.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top