(800) 853-2651
SHOP NOW

Recent content by Matthew L

Yesterday's Tractor Forums
  1. M

    Case 830 Comfort King

    Need some help on the wiring to and from the key switch. also I am going to a one wire alternator and a amp gauge . Need a little info. on the wiring setup also. Thanks, Muleman2
  2. W

    Attn. Chuck Machinist

    Still need to bust some rocks? Rock Crusher on FBM
  3. M

    Oliver 1855 Turbo Oil Line

    I am planning to build a stainless steel oil pan that is a few inches deeper and extend the pickup tube. Matthew L
  4. M

    Oliver 1855 Turbo Oil Line

    I am putting an 1855 back together that has the original (not oil cooler) block and my friends and I have forgotten where the oil line comes from and what line it is. It is kind of a long story, had all my stuff organized and it got moved. Can't find anything else on the internet that deals with...
  5. M

    Prettiest tractor....

    Large frame 55 series Oliver Red stripe 2-105 2-110 Workhorse Series IH 1206 IH 5X88 Series D21 Allis IH Magnums
  6. M

    Big lawn roller!

    I was rolling beans with a 15' Rite-Way and a 2-105 on the 18th. Should have took a picture!
  7. M

    US Tanker E. H. Blum 2/16/42

    Where is Lanse when we need him? I guess I'll ask for him-"Can I weld it with my 90 amp HF flux core?" LOL Matthew L
  8. M

    Ooooo, killer deal :)-

    When in doubt add more passes LOL Matthew L
  9. M

    Today's funny

    Saw that over on AgTalk a few days ago. Got a good laugh out of that!
  10. M

    Lanse-Question

    Are you going to National FFA Convention this year? Thanks, Matthew L
  11. M

    Today's funny

    Or in school like me LOL. Matthew L
  12. M

    Silage chopping

    The farm I work on bagged haylage with a 1755 Oliver (80-85HP) on a 9 foot bagger. The brakes stuck a little and there was enough pressure to split the bag in some spots just a little. Had no problems otherwise.
  13. M

    Cutting Aluminum

    1/8 wall sq. tubing and .063 sheet
  14. M

    Cutting Aluminum

    Hi everybody, I was wondering what the best way to cut aluminum tubing and sheet is. I have heard miter saw or skil saw, but I don't know what blades. Thanks, Matthew L
  15. M

    Mp210 welder

    I would buy it. I have one and have only used it MIG and stick welding. I love it. It is 40-175 stick and TIG amps IIRC. 14.0-25.0 volts for MIG welding. I am planning on getting a spoolgun to do aluminum. I think $800 is a good deal if it works well. Also DC only output. Sorry that I'm late to...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top