(800) 853-2651
SHOP NOW

Recent content by matthies

Yesterday's Tractor Forums
  1. M

    WTB - parts for kewanee auger with flip up hopper

    No luck, 3 broken ones and one well worn. Sorry.
  2. M

    4020 rear tires dilemmas

    Just get some good used tires on the larger rims and then replace tires as needed.
  3. M

    Replacing steering shaft bushing

    Don't be surprised if you have to take all the paint off from the steering wheel to the support to get the installed bushing back on. See how the bushing fits before you install it if you can.
  4. M

    “G” flipper guard ?

    Just put it on the pin like it is now, but to the left side. Hook end goes on arm of the flipper. Doubt it needs to be wound, but it might.
  5. M

    WTB - parts for kewanee auger with flip up hopper

    That sure looks familiar, will look tonite.
  6. M

    How to Remove this Seal from Cylinder?

    A drill and a screw then pull it out. But if it is leaking there is an oring/packing deeper which you need to totally disassemble. Waste of time to replace just that seal. The ram is in poor shape.
  7. M

    WTB - parts for kewanee auger with flip up hopper

    Could you post a pic of yours on here? There are some odd gears in my shop that may be what you need. How thick of material? Size of shaft?
  8. M

    Replacing steering shaft bushing

    Remove the steering wheel and the front bearing cap then unscrew the shaft from the tractor.
  9. M

    Guessing this is the right forum....question on a C-IH 895 PTO shaft leaking.

    By looking at the partsbook, you should be able to remove the three bolt cover and replace the seal. Years ago, I had to replace the pto shaft since it was snapped off, either too long of shaft on batwing mover or turned to short, but had to remove 3pt housing to get at a snap ring to replace...
  10. M

    6610 oil leak from clutch rod hole

    I replaced the boot on the rear axles with just my hands, had to do 2 tractors. Also resealed the brake through shaft while there. Havn't worked on these tractors a lot just recently. So will help with what I can. That rubber 4x5 plug is available, the one tractor was missing it.
  11. M

    Thread watched 1550 bull gear pinion removal, follow up

    Sorry, but can still use the hammer and work your way around the housing, the ears at the 2 and 8 position are going to be your helpers on getting this to move, just don't get carried away. LOL
  12. M

    Thread watched 1550 bull gear pinion removal, follow up

    A 2 lb hammer and punch and give the bolt the best you have. Helps loosen the bolt, I started doing this on manifold bolts, then when a bolt doesn't move, out comes the big hammer and punch.
  13. M

    Backhoe Questions

    Is there a serial tag by your right heel when sitting on it.
  14. M

    1550 Power Beyond

    Nice plumbing.
  15. M

    Different mowing job

    Trapped gophers since I was a teenager, showed my son and we did a few jobs together, $8 a gopher. He started working for a Ford New Holland dealership and seen the mounds, took a trap into work and caught the gopher, mowing guy was happy. He also scared the crap out of some of his coworkers...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top