(800) 853-2651
SHOP NOW

Recent content by mccormicksw4

Yesterday's Tractor Forums
  1. M

    M&W Governor fitment

    h-350 takes G-10 M&W m-450 takes G-11 M&W
  2. M

    M&W 9 speed instructions

    I bought an M&W 9speed kit to install in an H. I can find installation instructions online to install the cable operated kit but nothing for the rod controlled kit. I would prefer proper instructions to drill the hole etc when I do this job Does anyone have a copy? TIA
  3. M

    Farmall M/SM OEM & Aftermarket add ons

    you were kinda right. both styles were made by Monroe Hiesler made 9 speeds and hand clutches as well. I have never seen one buy the also made a manifold that used a 2 barrel carb
  4. M

    600 International

    4 5/8 inch bore would yield slightly under 370 cubes. I think you made a typo. and actually knew that
  5. M

    Engine stuck on 63 cub with new pistons and valves

    you are a bully Sir
  6. M
    Expired

    Wanted Farmall H M&W pistons and governor

    I am looking for a set of M&W pistons for a Farmall H. or a single piston if need be Also M&W governor for same
  7. M

    Ridge reaming piston cylinder. How much is too much?

    you haven't seen many engines then.
  8. M

    Aftermarket rear rim problems

    I just cut the the loops off with a cutoff wheel on grinder and installed the OEM square ones on the new rims. not too difficult, just measured the depth of the original ones and bolted the center on all 4 OEM sq. loops to hold the spacing
  9. M

    Aftermarket rear rim problems

    not necessarily . I just run into the same problem with 10" wide rims. they are not for a Cub
  10. M

    1961 farmall m replacement block

    gas heads have the same valves. distillate heads have different lengths than gas heads
  11. M

    can you swap 300 with a H motor?

    the 300 U has 1/2 " mounting holes and bolts for the front cover. Thread inserts are available to reduce the 1/2" threads down to the 3/8" threads needed to install the c153 front cover so long as its the later cover with wider distributor drive bolt pattern are you putting an H engine in a...
  12. M

    Super H engine

    I have put a few Utility engines in Farmalls. the front cover and block does have 1/2 holes and threads The first one I used allen socket cap screws which is fine after that I use thread inserts which are similar to heli coil repairs . They are available in 3/8- 16 internal to 1/2 -13...
  13. M

    Is it a W-4 or Super W-4?

    only thin Super I see is the IH emblem on the grille The starter is not the pull rod type but just a regular W4 style with a stud on it ( see pic) also the ammeter pod does not have the ignition switch located in it tear drop headlights also but that does not determine too much
  14. M

    W-4? Where and how much? Good, bad, other?

    I believe the weights found on the Internet are for a basic tractor- without starter, charging system,battery,pto, belt pulley attachement to mention he heavy options. They are slightly over 4000# not close to 3000# if that makes a difference to you if you have a lot of hills a Super may be...
  15. M

    remove SW4 starter - again !

    belt pulley, belt pulley gearbox but IH most likely called it a belt pulley attachment Rustred and I both properly described how to remove the starter. Old guys with sore fingers and poor keyboard skills may not articulate the process as well as others but if someone asks a question, he may need...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top