(800) 853-2651
SHOP NOW

Recent content by mdallisD17

Yesterday's Tractor Forums
  1. M

    Scammers using this site to push forward their trade.

    lucky me.
  2. M

    Scammers using this site to push forward their trade.

    what do i have to do with this??
  3. M

    murray 20 inch push mower carb replacement

    i have an X259630 behind/beside the carb. i have all plastics off cant seem to see anything else..
  4. M

    murray 20 inch push mower carb replacement

    link to briggs parts site https://shop.briggsandstratton.com/pages/parts-lookup#/Briggs_%26_Stratton_Power_Products/20606x30B_-_Walk-Behind_Mower_(2000)/Mower_Housing_Assembly/20606x30B/6537/y
  5. M

    murray 20 inch push mower carb replacement

    hey everyone hope all is well, i am having a hard time finding a carb part number for a 6.5 hp briggs motor on a murray push mower, anyone know something i dont know? they dont list the carb on the briggs website, here are the model and serial model 206006X30B serial 7413604704f00397
  6. M

    20 hp briggs and straton v twin intake push rod bending

    update!!!!!!!!!!!!! miracles do happen with the help of amazing people like yourselves. going on my fifth cut and fingers crossed it goes as well as the first four. my neighbor is a catepillar mechanic so i trusted him with the task of the loctite ing the shaft and he was pretty confident in...
  7. M

    20 hp briggs and straton v twin intake push rod bending

    yes, the solenoid on the carb, ok perfect i thought i remembered it being just a ground. and yes your colors are correct as well. thanks again, this forum and people on it are 10/10
  8. M

    20 hp briggs and straton v twin intake push rod bending

    one more stupid question. yu know the electronic needle and seat is the one pin strictly a ground wire, i seem to only have one wire going to the carb for this and dont have any wire in my parts container. is it this part 789A on briggs wiring diagram(on briggs website) part number 591391...
  9. M

    20 hp briggs and straton v twin intake push rod bending

    oh def low oil, i cant believe the strength of these motors, i will be honest i do zero maintenance to this old girl, it leaks all the oil you put in out the crank seal since new so i just stopped adding, when i do its old 15/40 from my 7.3 diesel. i have ran this thing for 20 years plus and...
  10. M

    20 hp briggs and straton v twin intake push rod bending

    1. yikes i am glad you told me about the shaft stays in its bore. what would have caused this to come out? . how would i go about fixing this, or is loctite the way to go? should i by a new one, will that help? it shows it as one part on the briggs website, shows the assembly and the washer...
  11. M

    20 hp briggs and straton v twin intake push rod bending

    i posted before asking about bending push rods i have taken motor apart and found this, (attached pics) 1- what is the piece sitting on the bottom left of pic, i am guessing something for the governor. can i just put this back into its seat or do i need a new one.(also how would it fall out)...
  12. M

    20 hp briggs and straton v twin intake push rod bending

    hey thanks for the reply. i had the head off and cleaned all that, tbh there wasnt much at all. i am leaning towards my crankshaft snapped in half the valves arent moving properly like the other side. it'll be my winter project.
  13. M

    20 hp briggs and straton v twin intake push rod bending

    hey thanks for reply. i took head off valve seat is fine the guide had moved which i though was problem, but didnt solve anything, i am guessing my camshaft snapped in halfor something cam related, i cant see valve marks hitting anything was all pretty normal inside.
  14. M

    20 hp briggs and straton v twin intake push rod bending

    hey everyone thanks for taking time to read, ill try be quick, was cutting boom misfire broke push exhaust push rod bent intake, replaced with new, adjusted them, mower starts full throttle wide open can slow with choke or manually pushing governor leaver on carb and will idle fine but will...
  15. M

    lift cylinder removal for three point hitch

See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top